[c-nsp] PA-2FE-TX using both ports kills module
Nikolai Schupbach
nikolai at net24.co.nz
Sun Sep 25 18:05:13 EDT 2005
Here is the crash dump output, you can see the ping just before the
crash. (I was pinging over the other interface at the same time). I can
only get it to crash in the 7200 non-VXR with NPE200; on the VXR /w
NPE400 it just seems to lock up the module.
Protocol [ip]:
Target IP address: 192.168.98.1
Repeat count [5]: 100000
Datagram size [100]: 1000
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 100000, 1000-byte ICMP Echos to 192.168.98.1, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!
%ERR-1-GT64010: Fatal error, Address parity error
cause=0x0100E183, mask=0x0CD01F00, real_cause=0x00000100
bus_err_high=0x00000000, bus_err_low=0x00000000, addr_decode_err=0x14000470
%ERR-1-SERR: PCI bus system/parity error
%ERR-1-FATAL: Fatal error interrupt, No reloading
err_stat=0x1, err_enable=0xFF, mgmt_event=0x8
System bridge dump:
Bridge 0, Downstream MB0 to MB1, Handle=0
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id = 0x00011011
(0x04):status, command = 0x02800143
(0x08):class code, revid = 0x06040002
(0x0C):hdr, lat timer, cls = 0x00010010
(0x18):sec lat,cls & bus no = 0x18000100
(0x1C):sec status, io base = 0x02809040
(0x20):mem base & limit = 0x4AF04880
(0x24):prefetch membase/lim = 0x4BF04B00
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00008020
(0x48):sec write attmp ctr = 0x00FFFFFF
(0x4C):pri write attmp ctr = 0x00FFFFFF
Bridge 1, Upstream MB1 to MB0, Handle=1
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id = 0x00011011
(0x04):status, command = 0x02800144
(0x08):class code, revid = 0x06040002
(0x0C):hdr, lat timer, cls = 0x0001F800
(0x18):sec lat,cls & bus no = 0x18090400
(0x1C):sec status, io base = 0x02809040
(0x20):mem base & limit = 0x4AF04880
(0x24):prefetch membase/lim = 0x4CF04B00
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00008020
(0x48):sec write attmp ctr = 0x00FFFFFF
(0x4C):pri write attmp ctr = 0x00FFFFFF
Bridge 2, Downstream MB0 to MB2, Handle=2
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id = 0x00011011
(0x04):status, command = 0x02800143
(0x08):class code, revid = 0x06040002
(0x0C):hdr, lat timer, cls = 0x00010010
(0x18):sec lat,cls & bus no = 0x18000200
(0x1C):sec status, io base = 0x0280F0A0
(0x20):mem base & limit = 0x4F704D00
(0x24):prefetch membase/lim = 0x4CF04C00
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00008020
(0x48):sec write attmp ctr = 0x00FFFFFF
(0x4C):pri write attmp ctr = 0x00FFFFFF
Bridge 3, Upstream MB2 to MB0, Handle=3
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id = 0x00011011
(0x04):status, command = 0x02800144
(0x08):class code, revid = 0x06040002
(0x0C):hdr, lat timer, cls = 0x0001F800
(0x18):sec lat,cls & bus no = 0x180F0A00
(0x1C):sec status, io base = 0x0280F0A0
(0x20):mem base & limit = 0x4F704D00
(0x24):prefetch membase/lim = 0x4CF04B00
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00008020
(0x48):sec write attmp ctr = 0x00FFFFFF
(0x4C):pri write attmp ctr = 0x00FFFFFF
PA bridge dump:
Bridge 4, Port Adaptor 1, Handle=1
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id = 0x00011011
(0x04):status, command = 0x02800147
(0x08):class code, revid = 0x06040002
(0x0C):hdr, lat timer, cls = 0x0001F800
(0x18):sec lat,cls & bus no = 0x18050504
(0x1C):sec status, io base = 0x22805040
Received Master Abort on secondary bus
(0x20):mem base & limit = 0x48F04880
(0x24):prefetch membase/lim = 0x0000FF00
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00009020
(0x48):sec write attmp ctr = 0x00FFFFFF
(0x4C):pri write attmp ctr = 0x00FFFFFF
Bridge 5, Port Adaptor 2, Handle=2
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id = 0x00011011
(0x04):status, command = 0x02800147
(0x08):class code, revid = 0x06040002
(0x0C):hdr, lat timer, cls = 0x0001F800
(0x18):sec lat,cls & bus no = 0x180B0B0A
(0x1C):sec status, io base = 0x0280B0A0
(0x20):mem base & limit = 0x4D704D00
(0x24):prefetch membase/lim = 0x0000FF00
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00009020
(0x48):sec write attmp ctr = 0x00FFFFFF
(0x4C):pri write attmp ctr = 0x00FFFFFF
Bridge 6, Port Adaptor 3, Handle=3
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id = 0x00011011
(0x04):status, command = 0x02800147
(0x08):class code, revid = 0x06040002
(0x0C):hdr, lat timer, cls = 0x0001F800
(0x18):sec lat,cls & bus no = 0x18060604
(0x1C):sec status, io base = 0x22807060
Received Master Abort on secondary bus
(0x20):mem base & limit = 0x49704900
(0x24):prefetch membase/lim = 0x0000FF00
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00009020
(0x48):sec write attmp ctr = 0x00FFFFFF
(0x4C):pri write attmp ctr = 0x00FFFFFF
Regards, Nikolai.
Rodney Dunn wrote:
>What does the cashinfo file look like?
>
>
>On Sun, Sep 25, 2005 at 01:13:24AM +1200, Nikolai Schupbach wrote:
>
>
>>Hello,
>>
>>We have a PA-2FE-TX in a 7206VXR /w NPE400. We have not be successful in
>>getting
>>both ports working in this module. If we run this module using a single port
>>everything is stable and fine. However as soon as we enabled the second port
>>and start passing traffic through this port, both ports will stop responding.
>>The only way to get the card to respond again is to remove and re-insert it.
>>(it does not crash the router)
>>
>>We thought this was due to a faulty PA-2FE-TX module, so we purchased another
>>one but we experience *exactly* the same problem. So we did some further tests
>>and tried to place these modules in a standard 7200 non-VXR /w NPE200 router,
>>and again we experience the same problem, with the exception of the 7200
>>non-VXR router crashing this time.
>>
>>We are running 12.3(15a), but we have tried with other IOS versions with no
>>luck. Here is the port diags from 1 of the ports:
>>
>>Slot 2:
>> Dual Port FastEthernet (RJ45) Port adapter, 2 ports
>> Port adapter is analyzed
>> Port adapter insertion time 06:58:34 ago
>> EEPROM contents at hardware discovery:
>> Hardware Revision : 1.0
>> PCB Serial Number : JAE091283VD
>> Part Number : 73-5419-06
>> Board Revision : B0
>> RMA Test History : 00
>> RMA Number : 0-0-0-0
>> RMA History : 00
>> Deviation Number : 0-0
>> Product (FRU) Number : PA-2FE-TX
>> Top Assy. Part Number : 800-08350-06
>> EEPROM format version 4
>> EEPROM contents (hex):
>> 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4A 41 45 30 39 31
>> 0x10: 32 38 33 56 44 82 49 15 2B 06 42 42 30 03 00 81
>> 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D
>> 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20
>> 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF
>> 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>> 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>> 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>>
>>Both cards have the same part and revision numbers.
>>
>>Has anyone heard of any problems with these cards? Two cards, purchased from
>>two
>>completely different companies, experience the same problem in two completely
>>separate routers. This has got me totally stumped.
>>
>>Regards, Nikolai.
>>
>>
>>_______________________________________________
>>cisco-nsp mailing list cisco-nsp at puck.nether.net
>>https://puck.nether.net/mailman/listinfo/cisco-nsp
>>archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>>
>
>!DSPAM:43356148308991919660288!
>
>
>
>
>
More information about the cisco-nsp
mailing list