[c-nsp] T-1 module card for Cisco 2811

[nealr]

 Chuck,

      Silly me - the WIC-1DSU-T1 requires version 2, as do some of the 
other single port devices with integrated CSU. I've just flipped open my 
February 2006 spiral bound sales guide and it would appear plain ol' 
VWIC-whatever are supported in the 28xx. This seems a little funny to me 
and I'm going to double check by plugging a first generation VWIC into a 
28xx on Monday because this is going to save us a lot of money, too.



                                                                                                          
Neal

Church, Chuck wrote:
> Neal,
>
> 	Are you saying the VWIC-2MFT-T1= won't work in a 2800/3800?
> Everything we've read said they will.  Just want to make sure.  We're
> currently ordering 2800s to replace a bunch of 2600s, hoping to not get
> hit with a big surprise...
>
> Thanks,
>
> Chuck Church
> Multimax Network Engineer, CCIE #8776
> EDS Contractor, Multimax - Navy Marine Corps Intranet (NMCI)
> 1210 N. Parker Rd. | Greenville, SC 29609 
> Office: 864-335-9473 | Cell: 864-266-3978
> cchurch at multimax.com
>  
> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net
> [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of nealr
> Sent: Saturday, December 02, 2006 1:25 PM
> To: Rudy Setiawan
> Cc: cisco-nsp at puck.nether.net
> Subject: Re: [c-nsp] T-1 module card for Cisco 2811
>
>
>    That is a correct part number for the 28xx series. The older 
> VWIC-2MFT would not work.
>
>    The card provides two channelized T1 controllers. If one wanted to 
> use these for data the steps would be defining the channels used which 
> will create a 'virtual' serial interface. If the desired effect is 3 
> mbits full duplex I would do this by assigning a /30 to each end of each
>
> circuit then using equal cost routing to load balance the links. There 
> may be some clever way to bond them with PPP so that the pair look like 
> a single interface but, alas, I am not terribly clever.
>
> Setting up controllers for data:
>
> controller T1 0/0/0
>  framing esf
>  linecode b8zs
>  channel-group 0 timeslots 1-24
> !
> controller T1 0/0/1
>  framing esf
>  linecode b8zs
>  channel-group 0 timeslots 1-24
>
>
> Example of how a serial interface created using the above commands would
>
> appear.
>
> interface Serial0/0/0:0
>  ip addr 192.168.0.1 255.255.255.0
>
>
>
>
> Rudy Setiawan wrote:
>   
>> Hi all,
>>
>> VWIC2-2MFT-T1/E1, does this module card allow the bonded(multilink)
>>     
> T-1?
>   
>> Or is it just based on software?
>>
>>
>> Thanks!
>>
>> Regards,
>> Rudy Setiawan
>>
>> _______________________________________________
>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>>   
>>     
>
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
>