[c-nsp] GSR Error - Power
Mike Johnson
harbor235 at gmail.com
Fri Sep 22 10:14:23 EDT 2006
Have you upgraded the IOS to a recent stable version as well as upgrading
all the linecard firmware. I seem to remember a bug that initiated this
message.
Check out:
http://www.cisco.com/en/US/products/hw/routers/ps167/products_tech_note09186a008009479d.shtml
mojo
On 9/22/06, Hank Nussbacher <hank at efes.iucc.ac.il> wrote:
>
> On Fri, 22 Sep 2006, Paul Stewart wrote:
>
> Just be happy that you are at least getting error messages. It could be
> worse, far worse:
>
>
> http://www.cisco.com/en/US/customer/products/hw/gatecont/ps821/products_field_notice09186a008073e19e.shtml
>
> "In the one known instance of mis-wiring, a reversal of the "live" and
> "ground" conductors in the appliance plug of the power cord set was found.
> If a mis-wired power cord set is connected to the power source, the
> chassis can become "live". Any contact with the chassis after it is
> connected to the power source could result in an electric shock."
>
> Fortunately no routers were damaged in this made for TV movie.
>
> :-)
>
> Regards,
> Hank Nussbacher
> http://www.interall.co.il
>
> > hi there...
> >
> > In our case, it was just that we didn't have the 2nd power supply wired
> > in yet....;) In your case, it sounds like whatever is in slot18 is
> > having an issue with high or low voltage...
> >
> > I'm sure someone on here can clarify what slot18 is... on our GSR it's a
> > switch fabric card..... hopefully not on yours....
> >
> > Paul
> >
> >
> > -----Original Message-----
> > From: Tantsura, Jeff [mailto:jtantsura at upcbroadband.com]
> > Sent: Friday, September 22, 2006 5:45 AM
> > To: Paul Stewart; cisco-nsp at puck.nether.net
> > Subject: RE: [c-nsp] GSR Error - Power
> >
> > Hi Paul,
> >
> > Same here: %ENV_MON-2-VOLTAGE: Card 1.5v supply(slot 18) volts has
> > reached CRITICAL level at 1600 m(V)
> >
> > Have you got any idea about how to deal with it?
> >
> > Regards,
> > Jeff
> >
> > P.S. sh env will show power related stuff
> >
> > -----Original Message-----
> > From: cisco-nsp-bounces at puck.nether.net
> > [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Paul Stewart
> > Sent: 20 September 2006 18:28
> > To: cisco-nsp at puck.nether.net
> > Subject: [c-nsp] GSR Error - Power
> >
> > Hi there...
> >
> > We just fired up a GSR here and I'm getting the following error:
> >
> > %ENV_MON-2-VOLTAGE: Card 5v supply(slot 26) volts has reached CRITICAL
> > level at 0 m(V)
> >
> > This GSR only has one of two DC power supplies online at the moment. Is
> > this error because only one power supply is online? The Cisco site
> > doesn't give us a lot of info... also is there a command on GSR that
> > shows "power status" ?
> >
> > Thanks,
> >
> > Paul Stewart
> > Network Administrator
> > Nexicom Inc.
> > http://www.nexicom.net/
> >
> > _______________________________________________
> > cisco-nsp mailing list cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
> > _______________________________________________
> > cisco-nsp mailing list cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
> > +++++++++++++++++++++++++++++++++++++++++++
> > This Mail Was Scanned By Mail-seCure System
> > at the Tel-Aviv University CC.
> >
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
More information about the cisco-nsp
mailing list