[c-nsp] Access Point & 2 SSID's Trunked to Vlan's

[Dan Letkeman]

Thanks!  Now the trunk is working and I can ping the ap.  I'm at home now
and I'll have to wait until tomorrow to test it out.

Thanks,
Dan.

On Dec 18, 2007 4:50 PM, Spaunhorst, Anamari <ASpaunhorst at uh.edu> wrote:

> Dan,
>
> Define your native Vlan on the DotRadio and the FastE interfaces. It has
> to match what you have configured on the port switch.
> you stated your native is vlan 500.
>
> Be sure you shutdown the DotRadio interfaces before making any changes
> on the wap.
>
>
>
> interface Dot11Radio0.160
> > > encapsulation dot1Q 160
> > > bridge-group 2
> > > !
> > > interface Dot11Radio0.500
> > > encapsulation dot1Q 500 native
> > > bridge-group 3
> > > !
> > > interface FastEthernet0.160
> > > encapsulation dot1Q 160
> > > bridge-group 2
> > > !
> > > interface FastEthernet0.500
> > > encapsulation dot1Q 500 native
> > > bridge-group 3
>
> write mem
> reload, then enable the DotRadio's
>
> Anna Spaunhorst
>
>
> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net
> [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Dan Letkeman
> Sent: Tuesday, December 18, 2007 4:35 PM
> To: Kaj Niemi; cisco-nsp at puck.nether.net
> Subject: Re: [c-nsp] Access Point & 2 SSID's Trunked to Vlan's
>
> Kaj,
>
> 2950#sh interfaces trunk
>
> Port        Mode         Encapsulation  Status        Native vlan
> Fa0/1       on           802.1q         trunking      500
>
> Port      Vlans allowed on trunk
> Fa0/1       160,200,500
>
> Port        Vlans allowed and active in management domain
> Fa0/1       160,200,500
>
> Port        Vlans in spanning tree forwarding state and not pruned
> Fa0/1       200
>
> Dan.
>
> On Dec 18, 2007 3:29 PM, Kaj Niemi <kajtzu at basen.net> wrote:
>
> > Hi,
> >
> > On Dec 18, 2007, at 23:00, Dan Letkeman wrote:
> >
> > > Here is my config
> > >
> > > Switch configuration:
> > >
> > > interface FastEthernet0/1
> > > switchport access vlan 500
> > > switchport trunk native vlan 500
> > > switchport trunk allowed vlan 160,200,500
> > > switchport mode trunk
> > >
> > > The trunk is only showing 200 in forwarding state.  I need 160 and
> 500
> > > forwarded.
> >
> > If you type on the upstream switch show interface ... trunk what does
> > it really show? usually the vlans allowed on the trunk, vlans allowed
> > and active and vlans in spanning-tree forwarding state and not pruned
> > are identical. Do you have vlans created for 160 and 500 on the switch
> > (assuming Cisco switch here)?
> >
> >
> > > interface Dot11Radio0.160
> > > encapsulation dot1Q 160
> > > bridge-group 2
> > > !
> > > interface Dot11Radio0.500
> > > encapsulation dot1Q 500
> > > bridge-group 3
> > > !
> > > interface FastEthernet0.160
> > > encapsulation dot1Q 160
> > > bridge-group 2
> > > !
> > > interface FastEthernet0.500
> > > encapsulation dot1Q 500
> > > bridge-group 3
> > > !
> > > interface BVI1
> > > ip address 192.168.50.151 255.255.255.0
> > > no ip route-cache
> > > !
> > > bridge 1 route ip
> > > !
> > >
> > > I'm guessing there is something wrong with the bridge configuration.
> >
> >
> >
> > Add:
> >
> > bridge 2 protocol ieee
> > bridge 3 protocol ieee
> >
> >
> >
> >
> >
> > HTH
> >
> > Kaj
> > --
> > Kaj J. Niemi
> > <kajtzu at basen.net>
> > +358 45 63 12000
> >
> >
> >
> >
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>