[c-nsp] 7204 PA-T3 PRoblem

[Jayson Navitsky]

Hi,

I have a PA-T3 in a 7204 (non VXR) NPE-200 for some reason no matter
what I do I cannot get this card to recognize any circuit attached to
it or give the appropriate lights.  I have noticed in show controllers
showing a "Last FEAC code received: unkonwn code 3F", (do note the
misspelling) Google has turned up nothing on this.

I have tried:
-New boot loader
-Various IOS versions
-Swapping out the PA-T3 with another one
-Different slots


With a hard loopback to the card here's the ouput:


Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-IS-M), Version 12.2(17f), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Wed 17-Aug-05 18:58 by tinhuang
Image text-base: 0x60008940, data-base: 0x61302000

ROM: System Bootstrap, Version 11.1(13)CA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc
1)
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(28d), RELEASE SOFTWARE (fc1)


XXXXXXX uptime is 3 minutes
System returned to ROM by power-on
Running default software

cisco 7204 (NPE200) processor (revision B) with 114688K/16384K bytes of memory.
Processor board ID 12164361
R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache
4 slot midplane, Version 1.0

Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
125K bytes of non-volatile configuration memory.
4096K bytes of packet SRAM memory.

62592K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102


Serial1/0 is down, line protocol is down
  Hardware is M1T-T3 pa
  MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation HDLC, crc 16, loopback not set
  Keepalive set (10 sec)
  Restart-Delay is 0 secs
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
              0 parity
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 applique, 4 interface resets
     0 output buffer failures, 0 output buffers swapped out
     5 carrier transitions
   rxLOS active, rxLOF inactive, rxAIS inactive
   txAIS inactive, rxRAI inactive, txRAI active

M1T-T3 pa: show controller:
PAS unit 0, subunit 0, f/w version 3-92, rev ID 0x2800001, version 3
idb = 0x62373D90, ds = 0x62375A88, ssb=0x62375DBC
Clock mux=0x30, ucmd_ctrl=0x0, port_status=0x0
Serial config=0x8, line config=0x1B0202
maxdgram=4584, bufpool=128Kb, 256 particles

   rxLOS active, rxLOF inactive, rxAIS inactive
   txAIS inactive, rxRAI inactive, txRAI active
line state: down
cable type : T3  cable, received clockrate n/a

base0 registers=0x3C800000, base1 registers=0x3C802000
rx_base0 registers=0x3C820000, rx_base1 registers=0x3C822000
mxt_ds=0x626D557C, rx ring entries=124, tx ring entries=254
statring=0x4B01D340, statr shadow=0x62377CBC, stat_head=0
plus_pa: rx_statring=0x4B01D780, rx_statr shadow=0x623784E8, rx_stat_head=0
rxring=0x4B01D100, rxr shadow=0x62377690, rx_head=0
txring=0x4B01DD40, txr shadow=0x62378914, tx_head=0, tx_tail=0, tx_count=0
throttled=0, enabled=0
halted=0, last halt reason=0
Microcode fatal errors=0
rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0
rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 0, bogus=0, mxt_flags=0x2C
tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=0(254)
tx_fullring=0, tx_started=0
rx_int_count=0, tx_int_count=0
   Framing is c-bit, Clock Source is Internal
   Bandwidth limit is 44210, DSU mode 0, Cable length is 150
   rx FEBE since last clear counter 41820, since reset 0
   Data in current interval (151 seconds elapsed):
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation
     0 P-bit Err Secs, 0 P-bit Sev Err Secs
     0 Sev Err Framing Secs, 150 Unavailable Secs
     0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs

   Transmitter is sending remote alarm.

   Receiver has loss of signal.
   Last FEAC code received: unkonwn code 3F




Thanks,
Jayson