[c-nsp] ISDN PRI on AS5300 12.2

[Shakeel Ahmad]

Please check physical connectivity

First Clue: Receiver has loss of frame.
Second : ISDN LAYER 1 needs to up before you diagnose further (and LAYER 1
will be up when your controller is up which is not)



On 3/8/07, vince anton <mvanton at gmail.com> wrote:
>
> Hi,
>
> here goes the E1 status as requested by oli:
>
> E1 0 is down.
> Applique type is Channelized E1 - balanced
> Receiver has loss of frame.
> alarm-trigger is not set
> Version info of slot 0:  HW: 1, PLD Rev: 11
> Framer Version: 0x8
>
> and here is the ISDN status:
>
> Global ISDN Switchtype = primary-net5
> ISDN Serial0:15 interface
>        dsl 0, interface ISDN Switchtype = primary-net5
>    Layer 1 Status:
>        DEACTIVATED
>    Layer 2 Status:
>        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
>    Layer 3 Status:
>        0 Active Layer 3 Call(s)
>    Active dsl 0 CCBs = 0
>    The Free Channel Mask:  0x00000000
>    Number of L2 Discards = 0, L2 Session ID = 0
>
>
>
> debugging gives absolutely no output :-(
>
> The only difference that I did not mention before is that the new 12.2 box
> has an 8 port E1 Card, while the working 12.1 box has a 4 port E1 card.
>
> dunno - perhaps the hardware is gone, but it was working ok until about a
> week ago with R2 type circuits.
>
> thanks
>
>
> anton
>
>
>
> On 07/03/07, Robert Carter <rcarter at kpu.net> wrote:
> >
> >  Good morning,
> >
> > Yes, for a better understanding, please send:
> >
> > sh isdn stat
> >
> > Then term mon and debug (if you can)
> >
> > debug isdn q921 (layer 2)
> >
> > That would help me in helping you... ;)
> >
> > Thanks,
> > Robert-
> >
> > vince anton wrote:
> >
> > On 07/03/07, Oliver Boehmer (oboehmer) <oboehmer at cisco.com> <
> oboehmer at cisco.com> wrote:
> >
> >  were there any major differences between 12.1 and 12.2 that require
> > different config for such setup ?
> >
> >  not that I'm aware of.. the E1 should come up. did you check with the
> > telco? What does "show controller e1 0" say?
> >
> >         oli
> >
> >
> >
> > Actually I moved the cable of a working ISDN circuit from the 12.1 box
> to
> > the 12.2
> >  box, so in this case I dont think its the telco - although I blame
> > them often :-)
> >
> > 'sh contr e1 0' says: 'E1 0 is down' - i'll get you the exact/full
> output.
> >
> > if there are any extra debugs that can help I can do that too.
> >
> >
> > Thanks,
> >
> > anton
> > _______________________________________________
> > cisco-nsp mailing list  cisco-nsp at puck.nether
> .nethttps://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
> >
> >
> >
>
>
> --
>
> Thanks,
>
> anton
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>