[c-nsp] ISDN PRI on AS5300 12.2

[vince anton]

Unbelievable but true........

I powered down the box - let it be for a few minutes, and powered it back
on.

and like magic it now works !!!

thought that applied for windows boxes only ;-)


thanks to all


anton


On 08/03/07, vince anton <mvanton at gmail.com> wrote:
>
> Hi,
>
> here goes the E1 status as requested by oli:
>
> E1 0 is down.
>   Applique type is Channelized E1 - balanced
>   Receiver has loss of frame.
>   alarm-trigger is not set
>   Version info of slot 0:  HW: 1, PLD Rev: 11
>   Framer Version: 0x8
>
> and here is the ISDN status:
>
> Global ISDN Switchtype = primary-net5
> ISDN Serial0:15 interface
>         dsl 0, interface ISDN Switchtype = primary-net5
>     Layer 1 Status:
>         DEACTIVATED
>     Layer 2 Status:
>         TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
>     Layer 3 Status:
>         0 Active Layer 3 Call(s)
>     Active dsl 0 CCBs = 0
>     The Free Channel Mask:  0x00000000
>     Number of L2 Discards = 0, L2 Session ID = 0
>
>
>
> debugging gives absolutely no output :-(
>
> The only difference that I did not mention before is that the new 12.2 box
> has an 8 port E1 Card, while the working 12.1 box has a 4 port E1 card.
>
> dunno - perhaps the hardware is gone, but it was working ok until about a
> week ago with R2 type circuits.
>
> thanks
>
>
> anton
>
>
>
> On 07/03/07, Robert Carter <rcarter at kpu.net> wrote:
> >
> >  Good morning,
> >
> > Yes, for a better understanding, please send:
> >
> > sh isdn stat
> >
> > Then term mon and debug (if you can)
> >
> > debug isdn q921 (layer 2)
> >
> > That would help me in helping you... ;)
> >
> > Thanks,
> > Robert-
> >
> > vince anton wrote:
> >
> > On 07/03/07, Oliver Boehmer (oboehmer) <oboehmer at cisco.com> <oboehmer at cisco.com> wrote:
> >
> >  were there any major differences between 12.1 and 12.2 that require
> > different config for such setup ?
> >
> >  not that I'm aware of.. the E1 should come up. did you check with the
> > telco? What does "show controller e1 0" say?
> >
> >         oli
> >
> >
> >
> > Actually I moved the cable of a working ISDN circuit from the 12.1 box to
> > the 12.2
> >  box, so in this case I dont think its the telco - although I blame
> > them often :-)
> >
> > 'sh contr e1 0' says: 'E1 0 is down' - i'll get you the exact/full output.
> >
> > if there are any extra debugs that can help I can do that too.
> >
> >
> >
> > Thanks,
> >
> > anton
> > _______________________________________________
> > cisco-nsp mailing list
> > cisco-nsp at puck.nether.nethttps://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
> >
> >
> >
>
>
> --
>
> Thanks,
>
> anton




-- 

Thanks,

anton