[c-nsp] SIP VoIP Config

[pmatusse at tdm.mz]

Hi Tom


Thank you. Adapted you config but still no working.

Can you please have a look on the debug output in attach.

Kind Regards

Pedro Wiliamo Matusse
Telecomunicações de Moçambique (TDM)
DSI
Tel. +258 21 482820
Cell. +258 82 3080780
Fax: +258 21 487812

----- Original Message -----
From: Tom Storey <tom at snnap.net>
Date: Tuesday, April 8, 2008 10:55 am
Subject: Re: [c-nsp] SIP VoIP Config

> Hi.
> 
> If it helps, I recently configured a 1760 to connect to my ISPs 
> VoIP  
> service, and this is the config I used for my sip-ua:
> 
> sip-ua
>  authentication username 08xxxxxxxx password xxxx
>  no remote-party-id
>  registrar ipv4:1.2.3.4 expires 3600
>  sip-server ipv4:1.2.3.4:5060
> !
> 
> Initially I had issues where my calls didnt appear to be dialled 
> via  
> the VoIP provider, but with a bit of debugging from both ends we  
> figured out that I had to "no" the "remote-party-id" feature, 
> hence  
> you see "no remote-party-id" line in my config.
> 
> The symptoms of my issue were I would dial the number, and it 
> would  
> sit there as if it were waiting for more characters, or it was 
> trying  
> to dial, and would eventually time out. It turns out it was 
> actually  
> dialling the number, but my VoIP provider was rejecting the call.
> 
> You can use "debug ccsip" to see SIP messages to/from your router, 
> 
> this can help to get clues about what it going on (beware that SIP 
> is  
> quite chatty, so a lot of output can be produced at times).
> 
> For reference, my dial-peers/voice-ports look like this:
> 
> voice-port 3/0
>  cptone AU
>  timeouts interdigit 4
>  timeouts call-disconnect 2
>  timeouts wait-release 10
>  description ** FXS right **
> !
> dial-peer voice 100 pots
>  destination-pattern 08........
>  port 3/0
> !
> dial-peer voice 200 voip
>  destination-pattern [0,1][2-4,7,8]........
>  session protocol sipv2
>  session target ipv4:1.2.3.4
>  dtmf-relay sip-notify rtp-nte
>  signal-type ext-signal
>  codec g711alaw
>  no vad
> !
> 
> Other than the config above, I have zero other config related to 
> voice  
> on this router - no translation rules, codec profiles, etc - the 
> above  
> two snips of config are it!
> 
> My setup is working 100% fine, inbound and outbound.
> 
> Hope that helps. :-)
> 
> Tom
> 
> On 08/04/2008, at 6:38 AM, <pmatusse at tdm.mz> 
<pmatusse at tdm.mz> wrote:
> 
> > Hi There,
> >
> >
> > Trying to make calls from a POTS do VOIP in SIP setup in attach, 
> calls> from POTS are not beeing forwarded to VoIP port.
> >
> > Can any one help
> >
> >
> >
> >
> >
> > Pedro Wiliamo Matusse
> > Telecomunicações de Moçambique (TDM)
> > DSI
> > Tel. +258 21 482820
> > Cell. +258 82 3080780
> > Fax: +258 21 487812
> > <config HJ3825 07 04 2008 23  
> > 00h.TXT>_______________________________________________
> > cisco-nsp mailing list  cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> 
>