[c-nsp] Cisco 7206VXR

[Tolstykh, Andrew]

Jason,

My issue was 100% specific to 12.4(19) - confirmed on 1 x 7204VXR and 1
x 7206VXR. Both routers were unable to boot the 12.4(19) IOS with
PA-2FE-FX card present (crash dump with the message that this code does
not support the installed port adapter). Changing the code to 12.4(8d)
resolved this issue on both routers.

-----Original Message-----
From: Jason Berenson [mailto:jason at pins.net] 
Sent: Friday, April 18, 2008 2:33 PM
To: Tolstykh, Andrew
Cc: Justin M. Streiner; cisco-nsp at puck.nether.net
Subject: Re: [c-nsp] Cisco 7206VXR

Andrew,

It looks like it may be this G1.  I'm testing another G1 with the T3 and

OC3 card in it and it seems to be happy but it's running: 
:c7200-js-mz.123-4.T1.bin right now.  I'm going to try 
c7200-is-mz.124-19.bin and see what happens.

-Jason

Tolstykh, Andrew wrote:
> Same issue with PID: PA-2FE-FX running on 12.4(19); crash dump on hard
> boot.
> Fixed by changing the image to 12.4(8d) - works like a charm. 12.4(17)
> should also work fine.
>
> HTH,
> Andrew
>
> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net
> [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Jason Berenson
> Sent: Friday, April 18, 2008 1:52 PM
> To: Justin M. Streiner
> Cc: cisco-nsp at puck.nether.net
> Subject: Re: [c-nsp] Cisco 7206VXR
>
> Justin, David,
>
> It crashes when I put the card in and keeps crashing on a reboot.  I
did
>
> get it to boot with 12.3.26.  When I put the PA-MC-T3 card in at that 
> point it's ok but when I put the ATM OC3 card in it crashes.
>
> When I have this router configured with an NPE-400 and these two cards

> it seems to work just fine.  I'm about to throw these 7206's out the 
> window and watch them slam into the pavement 10 floors down.
>
> -Jason
>
> Justin M. Streiner wrote:
>   
>> On Fri, 18 Apr 2008, Jason Berenson wrote:
>>
>>   
>>     
>>> I'm going to be upgrading a couple of 7206VXR NPE-350's to G1's
>>>       
> tomorrow
>   
>>> night.  I'm testing right now with the latest IP plus software:
>>> c7200-is-mz.124-19.bin.  When I pop in a PA-MC-T3 the router
promptly
>>> crashes:
>>>
>>> 10:44:58 UTC Fri Oct 8 2004: Data Bus Error exception, CPU signal
10,
>>> PC = 0x60
>>> 98AAA0
>>>
>>> --------------------------------------------------------------------
>>>   Possible software fault. Upon reccurence,  please collect
>>>   crashinfo, "show tech" and contact Cisco Technical Support.
>>> --------------------------------------------------------------------
>>>     
>>>       
>> You can try another version of code and see if that works better.  If
>>     
> not, 
>   
>> your best bet is to open a case with the TAC.
>>
>> Does the router crash when you insert any other port adapters?
>> Does the router crash regardless of which slot/bus you put the
>>     
> PA-MC-T3 
>   
>> in?
>> Is it a PA-MC-T3, or a PA-MC-T3+?
>>
>> jms
>> _______________________________________________
>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>   
>>     
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
>