[c-nsp] WS-X4506-GB-T Ports not connected

[Sebastian Wiesinger]

Hello,

I'm having a little problem here with a new Cisco 4510R-E. It's
running the following configuration:

Mod Ports Card Type                              Model        
---+-----+--------------------------------------+-------------
 5     6  Sup 6-E 10GE (X2), 1000BaseX (SFP)     WS-X45-SUP6-E
 9    18  1000BaseX (GBIC)                       WS-X4418-GB  
10     6  SFP, 10/100/1000BaseT (RJ45)V, Cisco/I WS-X4506-GB-T

 M MAC addresses                    Hw  Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
 5 0021.d808.6a00 to 0021.d808.6a05 1.1 12.2(44r)SG  12.2(40)SG       Ok       
 9 000c.3000.280a to 000c.3000.281b 1.1                               Ok       
10 001e.7ad0.f90c to 001e.7ad0.f911 1.4                               Ok       

Mod  Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+----------------------------------
 5   Active Supervisor   RPR                 Active                            

I'm tryubg to activate the ports on the WS-X4506-GB-T, but I'm unable to
get any connection. I connected the first two ports on the card to
create a loopback and still the ports are shown as "not connected". I
use RJ45 and have set the media-type of the ports to rj45 which
is also stated in the log:

00:00:05: %C4K_REDUNDANCY-6-INIT: Initializing as ACTIVE supervisor
00:00:05: 512 MB of system memory installed. Do 'show platform hardware sdram spd' for details.
00:00:37: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
00:00:38: %SYS-5-CONFIG_I: Configured from memory by console
00:00:38: %SYS-5-RESTART: System restarted --
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(40)SG, RELEASE SOFTWAR)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 07-Nov-07 19:52 by prod_rel_team
00:00:38: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 5 (WS-X45-SUP6-E S/N: JAE1222JOZS Hw: 1.1) is online
00:00:38: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 9 (WS-X4418-GB S/N: JAE07340WR1 Hw: 1.1) is online
00:00:38: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 10 (WS-X4506-GB-T S/N: JAE1218GSWU Hw: 1.4) is online
00:21:07: %C4K_IOSINTF-5-RJ45ACTIVE: Slot= 10 Port= 1:  RJ45 connector has become active
00:45:41: %C4K_IOSINTF-5-RJ45ACTIVE: Slot= 10 Port= 2:  RJ45 connector has become active

Here is the port configuration:

interface GigabitEthernet10/1
 no switchport
 ip address dhcp
 no keepalive
 media-type rj45
!
interface GigabitEthernet10/2
 no switchport
 ip address dhcp
 no keepalive
 media-type rj45
!

Is there anything I'm missing? I already changed the cabling so that's
not the problem. Any ideas/suggestions welcome.

Regards,

Sebastian



-- 
GPG Key-ID: 0x76B79F20 (0x1B6034F476B79F20)
'Are you Death?' ... IT'S THE SCYTHE, ISN'T IT? PEOPLE ALWAYS NOTICE THE SCYTHE.
            -- Terry Pratchett, The Fifth Elephant