[c-nsp] 6509 noob question

[Tassos Chatzithomaoglou]

The following two could probably help you too:

remote command switch xxx
remote login switch

--
Tassos


David Prall wrote on 25/3/2008 11:05 μμ:
> Switch console can only be done from catos. You want to find and entry that
> has a mac address within the cisco range. What does "sh cdp neighbor" give
> you. I don't remember this working, but it has been a long time. Then "sh
> cdp neighbor detail" for the address. Might get lucky.
> 
> David
> 
> --
> http://dcp.dcptech.com
>   
> 
>> -----Original Message-----
>> From: Adam Greene [mailto:maillist at webjogger.net] 
>> Sent: Tuesday, March 25, 2008 4:58 PM
>> To: David Prall; cisco-nsp at puck.nether.net
>> Subject: Re: [c-nsp] 6509 noob question
>>
>> Thanks, all.
>>
>> Neither the session nor switch console commands are 
>> recognized on the IOS 
>> side.
>>
>> Is there anything specific I should look for in the ARP 
>> table? There are 
>> about 1000 entries in there.
>>
>> I guess next step will be to call this switch's admin ....
>>
>> thanks,
>> Adam
>>
>> ----- Original Message ----- 
>> From: "David Prall" <dcp at dcptech.com>
>> To: "'Adam Greene'" <maillist at webjogger.net>; 
>> <cisco-nsp at puck.nether.net>
>> Sent: Tuesday, March 25, 2008 4:45 PM
>> Subject: RE: [c-nsp] 6509 noob question
>>
>>
>>> You need the management interface address for the catos 
>> side, from their 
>>> you
>>> can session to the msfc/msfc's. Can telnet from the msfc to 
>> the catos side
>>> if you know the address. Might be able to figure out where 
>> it is from the
>>> arp table.
>>>
>>> David
>>>
>>> --
>>> http://dcp.dcptech.com
>>>
>>>
>>>> -----Original Message-----
>>>> From: cisco-nsp-bounces at puck.nether.net
>>>> [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Adam Greene
>>>> Sent: Tuesday, March 25, 2008 4:20 PM
>>>> To: cisco-nsp at puck.nether.net
>>>> Subject: [c-nsp] 6509 noob question
>>>>
>>>> How's this for a stupid question?
>>>>
>>>> I'm working remotely on a pair of 6509's: CatOS 8.3(3) / IOS
>>>> 12.1(8a)E3.
>>>>
>>>> I can telnet to the devices and access the IOS CLI.
>>>>
>>>> The million-dollar question: how to I access the CatOS CLI?
>>>>
>>>> As far as I can tell all the switch configs live in CatOS
>>>> while the routing configs live in IOS, and I'm trying to gain
>>>> access to the spanning-tree info (CatOS), to see if the
>>>> switch is running PVST+, MST or what.
>>>>
>>>> Thanks,
>>>> Adam
>>>> _______________________________________________
>>>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>>>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>>>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>>
>>>
>>>
>>>
>>>
>>
>>
>>
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>