[c-nsp] RES: Cisco 12406 Etherchannel

[Oliver Boehmer (oboehmer)]

Mark,

you need 12.0(33)S to add SIP601 (it's an Engine5) GigE ports to a bundle.. take a look at the "Feature History" table in the link Leonardo quoted..

	oli

Mark Tech <> wrote on Tuesday, September 16, 2008 5:58 PM:

> Hi, thanks for that. Just had a look at my inventory
> 
> sh inventory
> NAME: "slot 0", DESCR: "ISE 10G Modular Services Card v2"
> PID: 12000-SIP-601     , VID: V04, SN: SAD12340460
> 
> Looks like I have an ISE card installed. If I look at the
> restrictions for the ISE, seems like only the following cards are
> supported:  
> 
> IP Service Engine (ISE):
> -4-port Gigabit Ethernet ISE line card
> -4-port OC-3c/STM-1c POS/SDH ISE line card
> -8-port OC-3c/STM-1c POS/SDH ISE line card
> -16-port OC-3c/STM-1c POS/SDH ISE line card
> -4-port OC-12c/STM-4c POS/SDH ISE line card
> -1-port OC-48c/STM-16c POS/SDH ISE line card
> 
> However it then goes to mention that the following cards support it.
> 
> Engine 5 SPA Interface Processors (SIPs):
> -10G Engine 5 SPA Interface Processor (12000-SIP-600)
> -2.5G multiservice engine SPA Interface Processor (12000-SIP-401)
> -5G multiservice engine SPA Interface Processor (12000-SIP-501)
> -10G multiservice engine SPA Interface Processor (12000-SIP-601)
> 
> The GE cards are installed in a 12000-SIP-601, or is that I don't
> have an'Engine 5' within the 601installed? 
> 
> Regards
> 
> Mark
> 
> 
> 
> ----- Original Message ----
> From: Leonardo Gama Souza <leonardo.souza at nec.com.br>
> To: Mark Tech <techconfig at yahoo.com>
> Cc: cisco-nsp at puck.nether.net
> Sent: Tuesday, September 16, 2008 3:49:54 PM
> Subject: RES: [c-nsp] Cisco 12406 Etherchannel
> 
> 
> There are some restrictions...
> Take a look:
> http://www.cisco.com/en/US/docs/ios/12_0s/feature/guide/lnkbndl.html 
> 
> Cheers.
> 
> ________________________________
> De: cisco-nsp-bounces at puck.nether.net em nome de Mark Tech
> Enviada: ter 16/9/2008 08:12
> Para: cisco-nsp at puck.nether.net
> Assunto: [c-nsp] Cisco 12406 Etherchannel
> 
> 
> Hi
> I am trying to configure Ethernchannel/link bundling on a 12406. The
> port channel seems to be accepted, however when I try and add a
> channel-group to my GE interfaces, it says its not supported? I am
> using SPA-10X1GE-V2 line cards with c12kprp-p-mz.120-32.SY6.bin IOS   
> 
> 
> interface Port-channel1
>  ip address x.x.x.x 255.255.255.252
>  no ip directed-broadcast
>  channel-group minimum active 1
>  no channel-group bandwidth control-propagation
> 
> router(config-if)#channel-group 1
> Error: not supported on GigabitEthernet0/0/0.
> 
> Is there a way to bundle more that 1GE port on a 12406?
> 
> Regards
> 
>  Mark
> 
> 
> 
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
> 
> 
> 
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/