[c-nsp] Rate limit Physical interface GSR

[Mark Tech]

Hi
tried the vlan policy map with standard and hierarchical but get the same issue when applying to an interface

policy-map gig-out
  class all-vlans
   police 64000 4470 4470
policy-map parent-gig-out
  class class-default
   service-policy gig-out

class-map match-all all-vlans
  match vlan  1-4095

(config)#int gigabitEthernet 0/0/6
(config-if)#service-policy output parent-gig-out
% 'match vlan/pseudowire' not supported in gig-out

The GSR cards  are 12000-SIP-601 and SPA-10X1GE-V2



----- Original Message ----
From: Oliver Boehmer (oboehmer) <oboehmer at cisco.com>
To: Mark Tech <techconfig at yahoo.com>; cisco-nsp at puck.nether.net
Sent: Thursday, April 9, 2009 3:33:43 PM
Subject: RE: [c-nsp] Rate limit Physical interface GSR

Hmm, can you replace the class-default with something like

class-map all-vlans
match vlan x y z ...

where x y z match your vlan IDs, and see if this changes things? What does "show policy-map int gig0/0/6" say? What type of linecard engine is this? E5/SIP?

vrf shouldn't make a difference..

    oli

Mark Tech <mailto:techconfig at yahoo.com> wrote on Thursday, April 09, 2009 16:20:

> Hi Oli
> 
> Thanks for that. I have tried that however I still see the interface
> as unaffected 
> 
> interface GigabitEthernet0/0/6
>  no ip address
>  no ip directed-broadcast
>  no negotiation auto
>  service-policy input gig-in
>  service-policy output gig-out
> 
> policy-map gig-out
>   class class-default
>    police 64000 4470 4470
> 
> policy-map gig-in
>   class class-default
>    police 64000 4470 4470
> 
> GigabitEthernet0/0/6 is up, line protocol is up
> 
>   5 minute input rate 915130000 bits/sec, 417475 packets/sec
>   5 minute output rate 915116000 bits/sec, 417467 packets/sec
> 
> 
> The sub-interfaces are in vrfs, will that affect this?
> 
> Cheers
> 
> Mark
> 
> 
> 
> 
> ----- Original Message ----
> From: Oliver Boehmer (oboehmer) <oboehmer at cisco.com>
> To: Mark Tech <techconfig at yahoo.com>; cisco-nsp at puck.nether.net
> Sent: Thursday, April 9, 2009 2:59:05 PM
> Subject: RE: [c-nsp] Rate limit Physical interface GSR
> 
> Mark Tech <> wrote on Thursday, April 09, 2009 13:15:
> 
>> Hi
>> I would like to cap a physical GE interface to 100mbps whist running
>> vlans through it on a GSR i.e.
>> 
> [...]
>> 
>> However when I apply  the rate-limit command on GE0/0/6, I don't see
>> any drop in traffic. Actually I have set up a throughput test through
>> GigabitEthernet0/0/6.2 running at 1Gbps which I can see through sh
>> int GigabitEthernet0/0/6 which does not drop to 100Mbps once the
>> rate-limit is added 
>> 
>> Is there a way to cap this aggregate interface?
> 
> On Engine3/5 linecards, you can use
> 
> policy-map gig-out
> class class-default
>   police 1000000000
> !
> int gig0/0/6
> service-policy output gig-out
> !
> int gig0/0/6.<vlan>
> ...
> 
> You can also use "match vlan" classes to provide differentiated
> treatment for vlans.. 
> 
>     oli