[c-nsp] SHDSL Wic in a 1751-1 CPE

Thu Aug 13 09:44:13 EDT 2009

I am testing a turnkey CPE solution combining T1, SDSL, ADSL and PRI 
handoff to customer PBX, with the 1751 transcoding SIP to PRI channels.

A CPE I am testing with a WIC-1SHDSL-V2 doesnt seem to be training 
properly. The controller continues to report

DSL firmware download in progress, please wait

I have had good experience with the ADSL wic, but the SHDSL wic seems to 
be far less useful.

Any tips or pointers would be greatly appreciated.

Thanks,

Joe

Router#sh controllers dsl 0/0

  DSL 0/0 controller DOWN
  SLOT 0: Globespan xDSL controller chipset
  DSL mode: Not Trained
  Frame mode: Utopia
  Configured Line rate: 2304Kbps
  Line Re-activated 0 times after system bootup
  LOSW Defect alarm: ACTIVE
  CRC per second alarm: ACTIVE
  Line termination: CPE
  FPGA Revision: 0xB2

         Current 15 min CRC: 0
         Current 15 min LOSW Defect: 0
         Current 15 min ES: 0
         Current 15 min SES: 0
         Current 15 min UAS: 833

         Previous 15 min CRC: 0
         Previous 15 min LOSW Defect: 0
         Previous 15 min ES: 0
         Previous 15 min SES: 0
         Previous 15 min UAS: 900

  Line-0 status
  Chipset Version:  0
  Firmware Version:  R3.0.1
  Modem Status:  Handshake, Status 10
  Last Fail Mode:  No Failure status:0x0
  DSL firmware download in progress, please wait
  Dying Gasp: Present

Router#sh inv
NAME: "1751-V chassis", DESCR: "1751-V chassis, Hw Serial#: 3808685901, 
Hw Revision: 0x600"
PID: 1751-V            , VID: 0x600, SN: FOC09331N37 (3808685901)

NAME: "Chassis Slot", DESCR: "1700 Chassis Slot"
PID: 1700 Chassis Slot , VID:    , SN:

NAME: "C1751 Mainboard", DESCR: "C1751 Mainboard"
PID: C1751 Mainboard   , VID: 0x600, SN: FOC09331N37 (3808685901)

NAME: "Daughter card slot:0", DESCR: "1700 DaughterCard Slot"
PID: 1700 DaughterCard Slot, VID:    , SN:

NAME: "WAN Interface Card - T1E1 or ATM (With GSHDSL-F module)", DESCR: 
"WAN Interface Card - T1E1 or ATM (With GSHDSL-F module)"
PID: WIC-1SHDSL-V2     , VID: V02 , SN: FOC085029XC

NAME: "ATM0/0", DESCR: "DSLSAR"
PID: DSLSAR            , VID:    , SN:

NAME: "Daughter card slot:1", DESCR: "1700 DaughterCard Slot"
PID: 1700 DaughterCard Slot, VID:    , SN:

NAME: "WAN Interface Card - Ethernet", DESCR: "WAN Interface Card - 
Ethernet"
PID: WIC-1ENET=        , VID: 3.0, SN: VMS06050AZH

NAME: "Ethernet1/0", DESCR: "PQUICC Ethernet"
PID: PQUICC Ethernet   , VID:    , SN:

NAME: "Daughter card slot:2", DESCR: "1700 DaughterCard Slot"
PID: 1700 DaughterCard Slot, VID:    , SN:

NAME: "One port T1 voice interface daughtercard", DESCR: "One port T1 
voice interface daughtercard"
PID: VWIC-1MFT-T1=     , VID: 1.0, SN: 31795887

NAME: "T1 2/0", DESCR: "T1 2/0"
PID: T1 2/0            , VID:    , SN:

NAME: "DSP Module Slot 0", DESCR: "Packet Voice DSP Module Slot 0"
PID: Packet Voice DSP Module Slot 0, VID:    , SN:

NAME: "DSP Module 0", DESCR: "Packet Voice DSP Module with 4 Unknown DSPs"
PID: Packet Voice DSP Module with 4 Unknown DSPs, VID: 2.2, SN: ICP0411000Z

NAME: "DSP Port 0/0", DESCR: "Unknown"
PID: Unknown           , VID:    , SN:

NAME: "DSP Port 0/1", DESCR: "Unknown"
PID: Unknown           , VID:    , SN:

NAME: "DSP Port 0/2", DESCR: "Unknown"
PID: Unknown           , VID:    , SN:

NAME: "DSP Port 0/3", DESCR: "Unknown"
PID: Unknown           , VID:    , SN:

NAME: "DSP Module Slot 1", DESCR: "Packet Voice DSP Module Slot 1"
PID: Packet Voice DSP Module Slot 1, VID:    , SN:

NAME: "FastEthernet0/0", DESCR: "PQUICC_FEC"
PID: PQUICC_FEC        , VID:    , SN:

Router#sh ver
Cisco IOS Software, C1700 Software (C1700-ADVENTERPRISEK9-M), Version 
12.4(25a), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Fri 22-May-09 20:24 by prod_rel_team

ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)

Router uptime is 7 hours, 14 minutes
System returned to ROM by reload
System image file is "flash:c1700-adventerprisek9-mz.124-25a.bin"

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be 
found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export at cisco.com.

Cisco 1751-V (MPC860P) processor (revision 0x600) with 118570K/12502K 
bytes of memory.
Processor board ID FOC09331N37 (3808685901), with hardware revision 0000
MPC860P processor: part number 5, mask 2
1 DSL controller
1 Ethernet interface
1 FastEthernet interface
1 ATM interface
1 Channelized T1/PRI port
32K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Router#sh conf | b DSL
controller DSL 0/0
  mode atm
  line-term cpe
  line-mode 2-wire line-zero
  dsl-mode shdsl symmetric annex A-B-ANFP
  line-rate 2304