[c-nsp] Cisco 4948-10GE

[Renelson Panosky]

I am trying to configure this trunk ports  between two Cisco 4948-10GE, the
ports would not come up here is an example of the error i got in one of the
ports


Take a look at port gi1/11 on each switch tell me what you think this error
mean:



On switch 1 it said not connect but on switch 2 it said (err-disabled)



Switch_1#sho int gi1/11

GigabitEthernet1/11 is down, line protocol is down (notconnect)

  Hardware is Gigabit Ethernet Port, address is 0027.0df3.0c8a (bia
0027.0df3.0c8a)

  MTU 9198 bytes, BW 1000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

  Auto-duplex, Auto-speed, link type is auto, media type is 10/100/1000-TX

  input flow-control is off, output flow-control is off

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input 4d00h, output never, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     1 packets input, 64 bytes, 0 no buffer

     Received 1 broadcasts (1 multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 input packets with dribble condition detected

     1 packets output, 64 bytes, 0 underruns

     0 output errors, 0 collisions, 2 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier

     0 output buffer failures, 0 output buffers swapped out





Switch_2#sho int gi1/11

GigabitEthernet1/11 is down, line protocol is down (err-disabled)

  Hardware is Gigabit Ethernet Port, address is 0027.0db3.67ca (bia
0027.0db3.67ca)

  MTU 9198 bytes, BW 1000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

  Auto-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000-TX

  input flow-control is off, output flow-control is off

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input 4d00h, output never, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     0 packets input, 0 bytes, 0 no buffer

     Received 0 broadcasts (0 multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 input packets with dribble condition detected

     0 packets output, 0 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier

     0 output buffer failures, 0 output buffers swapped out



I tried shut and no shut on the interface





Please help