[c-nsp] GSR 12008 GRP ISSUES

[Chris Lane]

All,
I have a GSR 12008 with 2 GRP-B route processors. Running
gsr-k4p-mz.120-32.S11.bin

My GRP failed over about 45 minutes ago to the backup in Slot1 from Slot0.
I keep getting this in my logs.
SEC  0:00:00:06: %MBUS-6-FIA_CONFIG: Switch Cards 0x1F (bit mask); Primary
Clock CSC_1
SEC  0:00:00:07: %FIA-3-HALT: To Fabric
SEC  0:00:00:07: %FIA-3-PARITYERR: To Fabric parity error was detected.
Request parity error interrupt = 0x4.
SEC  0:00:00:07: %FIA-3-HALT: To Fabric
SEC  0:00:00:07: %FIA-3-HALT: To Fabric
SEC  0:00:00:07: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
SEC  0:00:00:13: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
SEC  0:00:00:23: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
SEC  0:00:00:37: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3F4C 505A40D8 5059FCCC 502A02D8 502A02C4
SEC  0:00:00:44: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
SEC  0:00:01:08: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
SEC  0:00:01:15: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
SEC  0:00:01:39: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
SEC  0:00:01:56: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
SEC  0:00:02:10: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
SEC  0:00:02:41: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
SEC  0:00:02:48: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
SEC  0:00:03:12: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
SEC  0:00:03:43: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
SEC  0:00:03:50: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
SEC  0:00:04:14: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
SEC  0:00:04:45: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
timeout=0x6
-Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
SEC  0:00:05:02: %RP-3-FABRIC_UNI: Unicast send timed out  (1)
Jul 21 12:27:01.258 EDT: %RP-3-ERROR: Timed out while initializing IPC to
standby RP in slot 0
Jul 21 12:28:02.070 EDT: %MBUS-6-DEADSCDY: Standby RP in slot 0 timed out,
reset


Is this because SLOT0 is hung, trying to become primary again yet not
communicating with SLOT1 the active RP?
SLOT 0  (RP/LC 0 ): Route Processor
  MAIN: type 19,  800-2427-03 rev F0
        Deviation:  D070866
        HW config: 0x00    SW key: 00-00-00
  PCA:  73-2170-08 rev E0 ver 5
        Design Release 1.5  S/N SAD0745027R
  MBUS: MBUS Agent (1)  73-2146-07 rev B0 dev 0
        HW version 1.2  S/N CAT073504X3
        Test hist: 0x00    RMA#: 00-00-00    RMA hist: 0x00
  DIAG: Test count: 0x00000000    Test results: 0x00000000
  FRU:  Linecard/Module: GRP-B=
        Route Memory: MEM-GRP-512=
  MBUS Agent Software version 2.68 (RAM) (ROM version is 3.47)
  ROM Monitor version 2.2
  Primary clock is CSC 1
  Board State is Route Processor Powered ( RP  RDY )    ********* SHOULDN'T
THIS SAY STANDBY (STBY  RP )
  Insertion time: 42w1d (00:56:55 ago)
  DRAM size: 536870912 bytes


SLOT 1  (RP/LC 1 ): Route Processor
  MAIN: type 19,  800-2427-03 rev F0
        Deviation: 0
        HW config: 0x00    SW key: 00-00-00
  PCA:  73-2170-08 rev E0 ver 5
        Design Release 1.5  S/N SAD072000C3
  MBUS: MBUS Agent (1)  73-2146-07 rev B0 dev 0
        HW version 1.2  S/N CAT07100SFN
        Test hist: 0x00    RMA#: 00-00-00    RMA hist: 0x00
  DIAG: Test count: 0x00000000    Test results: 0x00000000
  FRU:  Linecard/Module: GRP-B=
        Route Memory: MEM-GRP-512=
  MBUS Agent Software version 2.68 (RAM) (ROM version is 3.47)
  ROM Monitor version 2.2
  Primary clock is CSC 1
  Board State is IOS Running  ACTIVE (ACTV  RP )
  Insertion time: 42w1d (00:56:55 ago)
  DRAM size: 536870912 bytes



Any help, suggestions greatly appreciated

Chris

-- 
//CL