[c-nsp] GSR 12008 GRP ISSUES
Aaron
dudepron at gmail.com
Tue Jul 21 17:07:16 EDT 2009
Looks like a fabric problem.
On Tue, Jul 21, 2009 at 14:34, Chris Lane <clane1875 at gmail.com> wrote:
> All,
> I have a GSR 12008 with 2 GRP-B route processors. Running
> gsr-k4p-mz.120-32.S11.bin
>
> My GRP failed over about 45 minutes ago to the backup in Slot1 from Slot0.
> I keep getting this in my logs.
> SEC 0:00:00:06: %MBUS-6-FIA_CONFIG: Switch Cards 0x1F (bit mask); Primary
> Clock CSC_1
> SEC 0:00:00:07: %FIA-3-HALT: To Fabric
> SEC 0:00:00:07: %FIA-3-PARITYERR: To Fabric parity error was detected.
> Request parity error interrupt = 0x4.
> SEC 0:00:00:07: %FIA-3-HALT: To Fabric
> SEC 0:00:00:07: %FIA-3-HALT: To Fabric
> SEC 0:00:00:07: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> SEC 0:00:00:13: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> SEC 0:00:00:23: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> SEC 0:00:00:37: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3F4C 505A40D8 5059FCCC 502A02D8 502A02C4
> SEC 0:00:00:44: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> SEC 0:00:01:08: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
> SEC 0:00:01:15: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> SEC 0:00:01:39: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
> SEC 0:00:01:56: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> SEC 0:00:02:10: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
> SEC 0:00:02:41: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
> SEC 0:00:02:48: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> SEC 0:00:03:12: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
> SEC 0:00:03:43: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
> SEC 0:00:03:50: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> SEC 0:00:04:14: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
> SEC 0:00:04:45: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003
> timeout=0x6
> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4
> SEC 0:00:05:02: %RP-3-FABRIC_UNI: Unicast send timed out (1)
> Jul 21 12:27:01.258 EDT: %RP-3-ERROR: Timed out while initializing IPC to
> standby RP in slot 0
> Jul 21 12:28:02.070 EDT: %MBUS-6-DEADSCDY: Standby RP in slot 0 timed out,
> reset
>
>
> Is this because SLOT0 is hung, trying to become primary again yet not
> communicating with SLOT1 the active RP?
> SLOT 0 (RP/LC 0 ): Route Processor
> MAIN: type 19, 800-2427-03 rev F0
> Deviation: D070866
> HW config: 0x00 SW key: 00-00-00
> PCA: 73-2170-08 rev E0 ver 5
> Design Release 1.5 S/N SAD0745027R
> MBUS: MBUS Agent (1) 73-2146-07 rev B0 dev 0
> HW version 1.2 S/N CAT073504X3
> Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00
> DIAG: Test count: 0x00000000 Test results: 0x00000000
> FRU: Linecard/Module: GRP-B=
> Route Memory: MEM-GRP-512=
> MBUS Agent Software version 2.68 (RAM) (ROM version is 3.47)
> ROM Monitor version 2.2
> Primary clock is CSC 1
> Board State is Route Processor Powered ( RP RDY ) ********* SHOULDN'T
> THIS SAY STANDBY (STBY RP )
> Insertion time: 42w1d (00:56:55 ago)
> DRAM size: 536870912 bytes
>
>
> SLOT 1 (RP/LC 1 ): Route Processor
> MAIN: type 19, 800-2427-03 rev F0
> Deviation: 0
> HW config: 0x00 SW key: 00-00-00
> PCA: 73-2170-08 rev E0 ver 5
> Design Release 1.5 S/N SAD072000C3
> MBUS: MBUS Agent (1) 73-2146-07 rev B0 dev 0
> HW version 1.2 S/N CAT07100SFN
> Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00
> DIAG: Test count: 0x00000000 Test results: 0x00000000
> FRU: Linecard/Module: GRP-B=
> Route Memory: MEM-GRP-512=
> MBUS Agent Software version 2.68 (RAM) (ROM version is 3.47)
> ROM Monitor version 2.2
> Primary clock is CSC 1
> Board State is IOS Running ACTIVE (ACTV RP )
> Insertion time: 42w1d (00:56:55 ago)
> DRAM size: 536870912 bytes
>
>
>
> Any help, suggestions greatly appreciated
>
> Chris
>
> --
> //CL
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
More information about the cisco-nsp
mailing list