[c-nsp] Help with understanding AS5400

[Andy Saykao]

Hey All,
 
I'm new to all this voice stuff...
 
We've just installed a AS5400 and plugged the PRI's in but I'm not
seeing the interfaces below show up in the config. 
 
Eg: 
interface Serial6/0:15
interface Serial6/1:15
interface Serial6/2:15
interface Serial6/3:15

The Carrier is seeing alarms on their end so it could be that the PRI's
aren't properly activated yet. But regardless of this, am I suppose to
see those serial interfaces present in the config irrespective of
whether the PRIs are up or not?
 
When I try to manually add in the interface, it's not recognized.
 
as1-ks(config)#interface serial 6/0:15?
% Unrecognized command

Some more details about the AS...
 
as1-ks#sh ver
Cisco IOS Software, 5400 Software (C5400-IS-M), Version 12.4(11)T,
RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Sun 19-Nov-06 00:33 by prod_rel_team
 
ROM: System Bootstrap, Version 12.1(2r)XD1, RELEASE SOFTWARE (fc1)
BOOTLDR: 5400 Software (C5400-BOOT-M), Version 12.1(5)T5,  RELEASE
SOFTWARE (fc1)
 
as1-ks-mel uptime is 40 minutes
System returned to ROM by reload at 15:53:14 AEST Tue Sep 29 2009
System restarted at 15:54:03 AEST Tue Sep 29 2009
System image file is "flash:c5400-is-mz.124-11.T.bin"
 
Cisco AS5400 (R7K) processor (revision T) with 262144K/65536K bytes of
memory.
Processor board ID JAB042904CY
R7000 CPU at 250MHz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3
Cache
Last reset from IOS reload
Manufacture Cookie Info:
 EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x31,
 Board Hardware Version 3.27, Item Number 800-5171-01,
 Board Revision B0, Serial Number JAB042904CY,
 PLD/ISP Version 2.2,  Manufacture Date 11-Jul-2000.
Processor 0x14, MAC Address 0001.42b3.5b7e
Backplane HW Revision 1.0, Flash Type 5V
2 FastEthernet interfaces
10 Serial interfaces
216 terminal lines
16 Channelized E1/PRI ports
512K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)
 
Configuration register is 0x2102

as1-ks#sh controllers e1 6/2
E1 6/2 is down.
  Applique type is Channelized E1 - balanced
  Far End Block Errors Detected
  Receiver has loss of signal.
  alarm-trigger is not set
  Version info of slot 6:  HW: 768, PLD Rev: 1
  Framer Version: 0x8

 
Thanks.
 
Andy

This email and any files transmitted with it are confidential and intended
 solely for the use of the individual or entity to whom they are addressed. 
Please notify the sender immediately by email if you have received this 
email by mistake and delete this email from your system. Please note that
 any views or opinions presented in this email are solely those of the
 author and do not necessarily represent those of the organisation. 
Finally, the recipient should check this email and any attachments for 
the presence of viruses. The organisation accepts no liability for any 
damage caused by any virus transmitted by this email.