[c-nsp] EOMPLS between 10G subinterface and GE subinterface between two 7600

[Tassos Chatzithomaoglou]

I'm running EoMPLS between 10GE subif and 1GE subif without any problem.

7600-a>sh mpls l2 vc 3601

Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- 
----------
Gi4/20.3601    Eth VLAN 3601              x.x.x.x         3601       UP


7600-b>sh mpls l2 vc 3601

Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- 
----------
Te3/2.3601     Eth VLAN 3601              x.x.x.x         3601       UP


Both 7600s are running SRD3.

--
Tassos

Ioan Branet wrote on 17/02/2010 10:49:
> Hello,
>
> We run EOMPLS on port and vlan mode on GE interfaces but we did not run
> EOMPLS Vlan mode between 10G and 1G subinterfaces until now.
>
> Any feedback is appreciated.
> Thank you,
> John
>
> On Wed, Feb 17, 2010 at 10:43 AM, Mikael Abrahamsson <swmike at swm.pp.se>wrote:
>
>   
>> On Wed, 17 Feb 2010, Ioan Branet wrote:
>>
>> You should answer to the list, answering just to me doesn't make much
>> sense.
>>
>> SRB4 is buggy, stop running it. Try latest SRB (SRB6 or 7, I don't
>> remember), or go SRD3 or later.
>>
>>
>>  Hello,
>>     
>>> We are running on both PEs the following:
>>> sh ver | i IOS
>>> Cisco IOS Software, c7600s72033_rp Software
>>> (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB4, RELEASE SOFTWARE
>>> (fc3)
>>>
>>> 10G card on PE1 is:
>>> show module 7
>>> Mod Ports Card Type                              Model              Serial
>>> No.
>>> --- ----- -------------------------------------- ------------------
>>> -----------
>>>  7    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE
>>> SAL1337YN4W
>>>
>>> and 1G on PE2 is:
>>>
>>>
>>> ro-sv01a-rd2#show module 2
>>> Mod Ports Card Type                              Model              Serial
>>> No.
>>> --- ----- -------------------------------------- ------------------
>>> -----------
>>>  2   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP
>>> SAL1005CBXG
>>>
>>> Mod MAC addresses                       Hw    Fw           Sw
>>> Status
>>> --- ---------------------------------- ------ ------------ ------------
>>> -------
>>>  2  0016.c8c4.fc10 to 0016.c8c4.fc27   2.3   12.2(14r)S5  12.2(33)SRB4 Ok
>>>
>>> Mod  Sub-Module                  Model              Serial       Hw
>>> Status
>>> ---- --------------------------- ------------------ ----------- -------
>>> -------
>>>  2  Centralized Forwarding Card WS-F6700-CFC       SAL1014J60S  2.0    Ok
>>>
>>> Mod  Online Diag Status
>>> ---- -------------------
>>>  2  Pass
>>>
>>> Thank you,
>>> John
>>>
>>> On Wed, Feb 17, 2010 at 10:27 AM, Mikael Abrahamsson <swmike at swm.pp.se
>>>       
>>>> wrote:
>>>>         
>>>  On Wed, 17 Feb 2010, Ioan Branet wrote:
>>>       
>>>>  GE interface between two 7600 as PE.
>>>>
>>>>         
>>>>>           
>>>> You forgot to include what software you're running.
>>>>
>>>> --
>>>> Mikael Abrahamsson    email: swmike at swm.pp.se
>>>>
>>>>
>>>>         
>> --
>> Mikael Abrahamsson    email: swmike at swm.pp.se
>>
>>     
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
>