[c-nsp] EOMPLS between 10G subinterface and GE subinterface between two 7600
Ioan Branet
ioan.branet at gmail.com
Wed Feb 17 16:58:13 EST 2010
Hello,
I used also vlan-tagging but with same result:
show configuration interfaces xe-3/1/0
description "** Link To PE1 **";
vlan-tagging;
link-mode full-duplex;
gigether-options {
no-auto-negotiation;
}
unit 999 {
bandwidth 10g;
vlan-id 999;
family inet {
accounting {
source-class-usage {
input;
}
}
no-redirects;
sampling {
input;
}
address 150.1.1.2/30 {
primary;
preferred;
}
}
}
#ping 150.1.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 150.1.1.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
On Wed, Feb 17, 2010 at 7:06 PM, Manu Chao <linux.yahoo at gmail.com> wrote:
> Hello,
>
> It is just a config problem on your J CE1: You needn't
> flexible-vlan-tagging (nor flexible-ethernet-services encapsulation)
>
> R/
> Manu
> On Wed, Feb 17, 2010 at 5:01 PM, Ioan Branet <ioan.branet at gmail.com>wrote:
>
>> Hello,
>>
>> I tried with Cisco 7600 as CE instead of Juniper and it works, I have to
>> find out what is wrong there.
>>
>> Thank you for your help,
>> Regards,
>> John
>>
>> ---------- Forwarded message ----------
>> From: Ioan Branet <ioan.branet at gmail.com>
>> Date: Wed, Feb 17, 2010 at 11:44 AM
>> Subject: Re: [c-nsp] EOMPLS between 10G subinterface and GE subinterface
>> between two 7600
>> To: Tassos Chatzithomaoglou <achatz at forthnet.gr>
>> Cc: cisco-nsp at puck.nether.net
>>
>>
>> Hello,
>>
>> Maybe there is a bug with SRB IOS.
>> I still have VC up on both ends but I cant ping between CE1 and CE2.
>>
>> On CE1 (Juniper side) I learn arp address of remote CE2 device and receive
>> arp request and send arp reply:
>>
>>
>> show arp no-resolve | match xe-3/1/0
>> 00:16:9c:6d:42:80 150.1.1.1 xe-3/1/0.999 none
>>
>>
>> Juniper PCAP Flags [Ext, In], PCAP Extension(s) total length 22
>> Device Media Type Extension TLV #3, length 1, value: Ethernet (1)
>> Logical Interface Encapsulation Extension TLV #6, length 1,
>> value:
>> Ethernet (14)
>> Device Interface Index Extension TLV #1, length 2, value: 193
>> Logical Interface Index Extension TLV #4, length 4, value: 126
>> Logical Unit Number Extension TLV #5, length 4, value: 32767
>> -----original packet-----
>> 0:16:9c:6d:42:80 > Broadcast, ethertype 802.1Q (0x8100), length 64:
>> vlan 999, p 0, ethertype ARP, arp who-has 150.1.1.2 tell 150.1.1.1
>> 11:34:01.878596 Out
>> Juniper PCAP Flags [Ext], PCAP Extension(s) total length 22
>> Device Media Type Extension TLV #3, length 1, value: Ethernet (1)
>> Logical Interface Encapsulation Extension TLV #6, length 1,
>> value:
>> Ethernet (14)
>> Device Interface Index Extension TLV #1, length 2, value: 193
>> Logical Interface Index Extension TLV #4, length 4, value: 126
>> Logical Unit Number Extension TLV #5, length 4, value: 32767
>> -----original packet-----
>> 0:21:59:a7:c4:30 > 0:16:9c:6d:42:80, ethertype 802.1Q (0x8100),
>> length 46: vlan 999, p 0, ethertype ARP, arp reply 150.1.1.2 is-at
>> 0:21:59:a7:c4:30.
>>
>> The issue is that I can't upgrade to SRD IOS.
>>
>> thank you,
>> John
>>
>>
>>
>> On Wed, Feb 17, 2010 at 11:05 AM, Tassos Chatzithomaoglou <
>> achatz at forthnet.gr> wrote:
>>
>> > I'm running EoMPLS between 10GE subif and 1GE subif without any problem.
>> >
>> > 7600-a>sh mpls l2 vc 3601
>> >
>> > Local intf Local circuit Dest address VC ID
>> Status
>> > ------------- -------------------------- --------------- ----------
>> > ----------
>> > Gi4/20.3601 Eth VLAN 3601 x.x.x.x 3601 UP
>> >
>> >
>> > 7600-b>sh mpls l2 vc 3601
>> >
>> > Local intf Local circuit Dest address VC ID
>> Status
>> > ------------- -------------------------- --------------- ----------
>> > ----------
>> > Te3/2.3601 Eth VLAN 3601 x.x.x.x 3601 UP
>> >
>> >
>> > Both 7600s are running SRD3.
>> >
>> > --
>> > Tassos
>> >
>> > Ioan Branet wrote on 17/02/2010 10:49:
>> >
>> >> Hello,
>> >>
>> >> We run EOMPLS on port and vlan mode on GE interfaces but we did not run
>> >> EOMPLS Vlan mode between 10G and 1G subinterfaces until now.
>> >>
>> >> Any feedback is appreciated.
>> >> Thank you,
>> >> John
>> >>
>> >> On Wed, Feb 17, 2010 at 10:43 AM, Mikael Abrahamsson <swmike at swm.pp.se
>> >> >wrote:
>> >>
>> >>
>> >>
>> >>> On Wed, 17 Feb 2010, Ioan Branet wrote:
>> >>>
>> >>> You should answer to the list, answering just to me doesn't make much
>> >>> sense.
>> >>>
>> >>> SRB4 is buggy, stop running it. Try latest SRB (SRB6 or 7, I don't
>> >>> remember), or go SRD3 or later.
>> >>>
>> >>>
>> >>> Hello,
>> >>>
>> >>>
>> >>>> We are running on both PEs the following:
>> >>>> sh ver | i IOS
>> >>>> Cisco IOS Software, c7600s72033_rp Software
>> >>>> (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB4, RELEASE
>> >>>> SOFTWARE
>> >>>> (fc3)
>> >>>>
>> >>>> 10G card on PE1 is:
>> >>>> show module 7
>> >>>> Mod Ports Card Type Model
>> >>>> Serial
>> >>>> No.
>> >>>> --- ----- -------------------------------------- ------------------
>> >>>> -----------
>> >>>> 7 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE
>> >>>> SAL1337YN4W
>> >>>>
>> >>>> and 1G on PE2 is:
>> >>>>
>> >>>>
>> >>>> ro-sv01a-rd2#show module 2
>> >>>> Mod Ports Card Type Model
>> >>>> Serial
>> >>>> No.
>> >>>> --- ----- -------------------------------------- ------------------
>> >>>> -----------
>> >>>> 2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
>> >>>> SAL1005CBXG
>> >>>>
>> >>>> Mod MAC addresses Hw Fw Sw
>> >>>> Status
>> >>>> --- ---------------------------------- ------ ------------
>> ------------
>> >>>> -------
>> >>>> 2 0016.c8c4.fc10 to 0016.c8c4.fc27 2.3 12.2(14r)S5
>> 12.2(33)SRB4
>> >>>> Ok
>> >>>>
>> >>>> Mod Sub-Module Model Serial Hw
>> >>>> Status
>> >>>> ---- --------------------------- ------------------ -----------
>> -------
>> >>>> -------
>> >>>> 2 Centralized Forwarding Card WS-F6700-CFC SAL1014J60S 2.0
>> >>>> Ok
>> >>>>
>> >>>> Mod Online Diag Status
>> >>>> ---- -------------------
>> >>>> 2 Pass
>> >>>>
>> >>>> Thank you,
>> >>>> John
>> >>>>
>> >>>> On Wed, Feb 17, 2010 at 10:27 AM, Mikael Abrahamsson <
>> swmike at swm.pp.se
>> >>>>
>> >>>>
>> >>>>> wrote:
>> >>>>>
>> >>>>>
>> >>>> On Wed, 17 Feb 2010, Ioan Branet wrote:
>> >>>>
>> >>>>
>> >>>>> GE interface between two 7600 as PE.
>> >>>>>
>> >>>>>
>> >>>>>
>> >>>>>>
>> >>>>>>
>> >>>>> You forgot to include what software you're running.
>> >>>>>
>> >>>>> --
>> >>>>> Mikael Abrahamsson email: swmike at swm.pp.se
>> >>>>>
>> >>>>>
>> >>>>>
>> >>>>>
>> >>>> --
>> >>> Mikael Abrahamsson email: swmike at swm.pp.se
>> >>>
>> >>>
>> >>>
>> >> _______________________________________________
>> >> cisco-nsp mailing list cisco-nsp at puck.nether.net
>> >> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> >> archive at http://puck.nether.net/pipermail/cisco-nsp/
>> >>
>> >>
>> >>
>> >
>> > _______________________________________________
>> > cisco-nsp mailing list cisco-nsp at puck.nether.net
>> > https://puck.nether.net/mailman/listinfo/cisco-nsp
>> > archive at http://puck.nether.net/pipermail/cisco-nsp/
>> >
>> _______________________________________________
>> cisco-nsp mailing list cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>
>
--
Ioan Branet
CCIE #23474 R&S
More information about the cisco-nsp
mailing list