[c-nsp] EOMPLS between 10G subinterface and GE subinterface between two 7600
Manu Chao
linux.yahoo at gmail.com
Thu Feb 18 15:09:36 EST 2010
switchport nonegociate missing on the pe?
2010/2/17, Ioan Branet <ioan.branet at gmail.com>:
> Hello,
>
> I used also vlan-tagging but with same result:
>
> show configuration interfaces xe-3/1/0
> description "** Link To PE1 **";
> vlan-tagging;
> link-mode full-duplex;
> gigether-options {
> no-auto-negotiation;
> }
> unit 999 {
> bandwidth 10g;
> vlan-id 999;
> family inet {
> accounting {
> source-class-usage {
> input;
> }
> }
> no-redirects;
> sampling {
> input;
> }
> address 150.1.1.2/30 {
> primary;
> preferred;
> }
> }
> }
>
> #ping 150.1.1.2
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 150.1.1.2, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
>
> On Wed, Feb 17, 2010 at 7:06 PM, Manu Chao <linux.yahoo at gmail.com> wrote:
>
>> Hello,
>>
>> It is just a config problem on your J CE1: You needn't
>> flexible-vlan-tagging (nor flexible-ethernet-services encapsulation)
>>
>> R/
>> Manu
>> On Wed, Feb 17, 2010 at 5:01 PM, Ioan Branet <ioan.branet at gmail.com>wrote:
>>
>>> Hello,
>>>
>>> I tried with Cisco 7600 as CE instead of Juniper and it works, I have to
>>> find out what is wrong there.
>>>
>>> Thank you for your help,
>>> Regards,
>>> John
>>>
>>> ---------- Forwarded message ----------
>>> From: Ioan Branet <ioan.branet at gmail.com>
>>> Date: Wed, Feb 17, 2010 at 11:44 AM
>>> Subject: Re: [c-nsp] EOMPLS between 10G subinterface and GE subinterface
>>> between two 7600
>>> To: Tassos Chatzithomaoglou <achatz at forthnet.gr>
>>> Cc: cisco-nsp at puck.nether.net
>>>
>>>
>>> Hello,
>>>
>>> Maybe there is a bug with SRB IOS.
>>> I still have VC up on both ends but I cant ping between CE1 and CE2.
>>>
>>> On CE1 (Juniper side) I learn arp address of remote CE2 device and
>>> receive
>>> arp request and send arp reply:
>>>
>>>
>>> show arp no-resolve | match xe-3/1/0
>>> 00:16:9c:6d:42:80 150.1.1.1 xe-3/1/0.999 none
>>>
>>>
>>> Juniper PCAP Flags [Ext, In], PCAP Extension(s) total length 22
>>> Device Media Type Extension TLV #3, length 1, value: Ethernet
>>> (1)
>>> Logical Interface Encapsulation Extension TLV #6, length 1,
>>> value:
>>> Ethernet (14)
>>> Device Interface Index Extension TLV #1, length 2, value: 193
>>> Logical Interface Index Extension TLV #4, length 4, value: 126
>>> Logical Unit Number Extension TLV #5, length 4, value: 32767
>>> -----original packet-----
>>> 0:16:9c:6d:42:80 > Broadcast, ethertype 802.1Q (0x8100), length
>>> 64:
>>> vlan 999, p 0, ethertype ARP, arp who-has 150.1.1.2 tell 150.1.1.1
>>> 11:34:01.878596 Out
>>> Juniper PCAP Flags [Ext], PCAP Extension(s) total length 22
>>> Device Media Type Extension TLV #3, length 1, value: Ethernet
>>> (1)
>>> Logical Interface Encapsulation Extension TLV #6, length 1,
>>> value:
>>> Ethernet (14)
>>> Device Interface Index Extension TLV #1, length 2, value: 193
>>> Logical Interface Index Extension TLV #4, length 4, value: 126
>>> Logical Unit Number Extension TLV #5, length 4, value: 32767
>>> -----original packet-----
>>> 0:21:59:a7:c4:30 > 0:16:9c:6d:42:80, ethertype 802.1Q (0x8100),
>>> length 46: vlan 999, p 0, ethertype ARP, arp reply 150.1.1.2 is-at
>>> 0:21:59:a7:c4:30.
>>>
>>> The issue is that I can't upgrade to SRD IOS.
>>>
>>> thank you,
>>> John
>>>
>>>
>>>
>>> On Wed, Feb 17, 2010 at 11:05 AM, Tassos Chatzithomaoglou <
>>> achatz at forthnet.gr> wrote:
>>>
>>> > I'm running EoMPLS between 10GE subif and 1GE subif without any
>>> > problem.
>>> >
>>> > 7600-a>sh mpls l2 vc 3601
>>> >
>>> > Local intf Local circuit Dest address VC ID
>>> Status
>>> > ------------- -------------------------- --------------- ----------
>>> > ----------
>>> > Gi4/20.3601 Eth VLAN 3601 x.x.x.x 3601 UP
>>> >
>>> >
>>> > 7600-b>sh mpls l2 vc 3601
>>> >
>>> > Local intf Local circuit Dest address VC ID
>>> Status
>>> > ------------- -------------------------- --------------- ----------
>>> > ----------
>>> > Te3/2.3601 Eth VLAN 3601 x.x.x.x 3601 UP
>>> >
>>> >
>>> > Both 7600s are running SRD3.
>>> >
>>> > --
>>> > Tassos
>>> >
>>> > Ioan Branet wrote on 17/02/2010 10:49:
>>> >
>>> >> Hello,
>>> >>
>>> >> We run EOMPLS on port and vlan mode on GE interfaces but we did not
>>> >> run
>>> >> EOMPLS Vlan mode between 10G and 1G subinterfaces until now.
>>> >>
>>> >> Any feedback is appreciated.
>>> >> Thank you,
>>> >> John
>>> >>
>>> >> On Wed, Feb 17, 2010 at 10:43 AM, Mikael Abrahamsson <swmike at swm.pp.se
>>> >> >wrote:
>>> >>
>>> >>
>>> >>
>>> >>> On Wed, 17 Feb 2010, Ioan Branet wrote:
>>> >>>
>>> >>> You should answer to the list, answering just to me doesn't make much
>>> >>> sense.
>>> >>>
>>> >>> SRB4 is buggy, stop running it. Try latest SRB (SRB6 or 7, I don't
>>> >>> remember), or go SRD3 or later.
>>> >>>
>>> >>>
>>> >>> Hello,
>>> >>>
>>> >>>
>>> >>>> We are running on both PEs the following:
>>> >>>> sh ver | i IOS
>>> >>>> Cisco IOS Software, c7600s72033_rp Software
>>> >>>> (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB4, RELEASE
>>> >>>> SOFTWARE
>>> >>>> (fc3)
>>> >>>>
>>> >>>> 10G card on PE1 is:
>>> >>>> show module 7
>>> >>>> Mod Ports Card Type Model
>>> >>>> Serial
>>> >>>> No.
>>> >>>> --- ----- -------------------------------------- ------------------
>>> >>>> -----------
>>> >>>> 7 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE
>>> >>>> SAL1337YN4W
>>> >>>>
>>> >>>> and 1G on PE2 is:
>>> >>>>
>>> >>>>
>>> >>>> ro-sv01a-rd2#show module 2
>>> >>>> Mod Ports Card Type Model
>>> >>>> Serial
>>> >>>> No.
>>> >>>> --- ----- -------------------------------------- ------------------
>>> >>>> -----------
>>> >>>> 2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
>>> >>>> SAL1005CBXG
>>> >>>>
>>> >>>> Mod MAC addresses Hw Fw Sw
>>> >>>> Status
>>> >>>> --- ---------------------------------- ------ ------------
>>> ------------
>>> >>>> -------
>>> >>>> 2 0016.c8c4.fc10 to 0016.c8c4.fc27 2.3 12.2(14r)S5
>>> 12.2(33)SRB4
>>> >>>> Ok
>>> >>>>
>>> >>>> Mod Sub-Module Model Serial Hw
>>> >>>> Status
>>> >>>> ---- --------------------------- ------------------ -----------
>>> -------
>>> >>>> -------
>>> >>>> 2 Centralized Forwarding Card WS-F6700-CFC SAL1014J60S 2.0
>>> >>>> Ok
>>> >>>>
>>> >>>> Mod Online Diag Status
>>> >>>> ---- -------------------
>>> >>>> 2 Pass
>>> >>>>
>>> >>>> Thank you,
>>> >>>> John
>>> >>>>
>>> >>>> On Wed, Feb 17, 2010 at 10:27 AM, Mikael Abrahamsson <
>>> swmike at swm.pp.se
>>> >>>>
>>> >>>>
>>> >>>>> wrote:
>>> >>>>>
>>> >>>>>
>>> >>>> On Wed, 17 Feb 2010, Ioan Branet wrote:
>>> >>>>
>>> >>>>
>>> >>>>> GE interface between two 7600 as PE.
>>> >>>>>
>>> >>>>>
>>> >>>>>
>>> >>>>>>
>>> >>>>>>
>>> >>>>> You forgot to include what software you're running.
>>> >>>>>
>>> >>>>> --
>>> >>>>> Mikael Abrahamsson email: swmike at swm.pp.se
>>> >>>>>
>>> >>>>>
>>> >>>>>
>>> >>>>>
>>> >>>> --
>>> >>> Mikael Abrahamsson email: swmike at swm.pp.se
>>> >>>
>>> >>>
>>> >>>
>>> >> _______________________________________________
>>> >> cisco-nsp mailing list cisco-nsp at puck.nether.net
>>> >> https://puck.nether.net/mailman/listinfo/cisco-nsp
>>> >> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>> >>
>>> >>
>>> >>
>>> >
>>> > _______________________________________________
>>> > cisco-nsp mailing list cisco-nsp at puck.nether.net
>>> > https://puck.nether.net/mailman/listinfo/cisco-nsp
>>> > archive at http://puck.nether.net/pipermail/cisco-nsp/
>>> >
>>> _______________________________________________
>>> cisco-nsp mailing list cisco-nsp at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>>
>>
>>
>
>
> --
> Ioan Branet
> CCIE #23474 R&S
>
--
Envoyé avec mon mobile
More information about the cisco-nsp
mailing list