[c-nsp] ME3600X Netflow and WCCP?

[Waris Sagheer (waris)]

ME3600X does not support Netflow and WCCP in the current release.
If the configuration guide does not cover the features then it is not be supported.
Netflow and WCCP features are not covered in the configuration guide.

-Waris


-----Original Message-----
From: cisco-nsp-bounces at puck.nether.net [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Colby Glass
Sent: Wednesday, July 27, 2011 4:27 PM
To: Sigurbjörn Birkir Lárusson
Cc: cisco-nsp at puck.nether.net
Subject: Re: [c-nsp] ME3600X Netflow and WCCP?

Thanks guys. Before posting, I noticed that it's listed in the unsupported
commands of an older IOS, but not in the newer one. That gave me some hope.
Though, none of the guides I saw listed anything for configuring WCCP or
Netflow. The feature nav listed WCCP Version 2 though. It's not looking
good.

On Wed, Jul 27, 2011 at 5:59 PM, Sigurbjörn Birkir Lárusson <
sigurbjornl at vodafone.is> wrote:

> I wouldn't trust that, you can configure stuff on the ME3600X that doesn't
> actually work (or in fact do anything at all) in practice, you can even
> configure stuff that is in the manual, and is supposed to work, but still
> doesn't work ;)
>
> I turned on flow on a couple of interfaces, turned on top-talkers and got
> nothing.  I then setup netcat to listen to a UDP port, configured export
> to send it, and according to show ip flow export it's not exporting
> anything.
>
> It also doesn't bode well for the support that ip flow-export is in the
> list of unsupported commands in the configuration guide, nor does the fact
> that there is only one reference to wccp in the configuration guide and
> that's under the traffic-classifier for the CPU traffic...
>
> Kind regards,
> Sibbi
>
> Þann 27.7.2011 21:31, skrifaði "Jason Lixfeld" <jason at lixfeld.ca>:
>
> >On 2011-07-27, at 4:45 PM, Colby Glass wrote:
> >
> >> All,
> >>
> >> Does anyone happen to know if the ME3600 supports Netflow and WCCP? I
> >>have a
> >> customer considering them for the WAN edge and the docs/feature
> >>navigator
> >> are coming up somewhat ambiguous.
> >
> >I haven't tested it, but...
> >
> >systems02.151front71(config)#ip flow-?
> >flow-aggregation  flow-cache        flow-capture  flow-egress
> >flow-export       flow-top-talkers
> >
> >systems02.151front71(config)#ip flow-export ?
> >  destination  Specify the Destination IP address
> >  source       Specify the interface for source address
> >  template     Specify the template specific configurations
> >  version      Specify the version number
> >
> >systems02.151front71(config)#ip flow-export version ?
> >  1
> >  5
> >  9
> >
> >systems02.151front71(config)#int g0/1
> >systems02.151front71(config-if)#no switchport
> >systems02.151front71(config-if)#ip route-cache ?
> >  cef             Enable Cisco Express Forwarding
> >  flow            Enable Flow fast-switching cache
> >  policy          Enable fast-switching policy cache for outgoing packets
> >  same-interface  Enable fast-switching on the same interface
> >  <cr>
> >
> >systems02.151front71(config-if)#ip wccp ?
> >  <0-254>    Dynamically defined service identifier number
> >  redirect   Set packet redirection options
> >  web-cache  Standard web caching service
> >
> >systems02.151front71(config-if)#
> >
> >This is on 12.2(52)EY1
> >_______________________________________________
> >cisco-nsp mailing list  cisco-nsp at puck.nether.net
> >https://puck.nether.net/mailman/listinfo/cisco-nsp
> >archive at http://puck.nether.net/pipermail/cisco-nsp/
>
>


-- 
Colby Glass
Network Engineer
http://blog.alwaysthenetwork.com
_______________________________________________
cisco-nsp mailing list  cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/