[c-nsp] ME3600X Netflow and WCCP?

[Reuben Farrelly]

What sort of timeframes are we now looking at for the next release of 
code for the ME3600/3800X's?  There was some talk about new software 
supporting VPLS related features coming out in June, and a bunch of 
15.0(SE) releases has just turned up on CCO for the lower end floor 
switches like the 3560/3750s..

Reuben


On 28/07/2011 9:50 AM, Waris Sagheer (waris) wrote:
> ME3600X does not support Netflow and WCCP in the current release.
> If the configuration guide does not cover the features then it is not be supported.
> Netflow and WCCP features are not covered in the configuration guide.
>
> -Waris
>
>
> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Colby Glass
> Sent: Wednesday, July 27, 2011 4:27 PM
> To: Sigurbjörn Birkir Lárusson
> Cc: cisco-nsp at puck.nether.net
> Subject: Re: [c-nsp] ME3600X Netflow and WCCP?
>
> Thanks guys. Before posting, I noticed that it's listed in the unsupported
> commands of an older IOS, but not in the newer one. That gave me some hope.
> Though, none of the guides I saw listed anything for configuring WCCP or
> Netflow. The feature nav listed WCCP Version 2 though. It's not looking
> good.
>
> On Wed, Jul 27, 2011 at 5:59 PM, Sigurbjörn Birkir Lárusson<
> sigurbjornl at vodafone.is>  wrote:
>
>> I wouldn't trust that, you can configure stuff on the ME3600X that doesn't
>> actually work (or in fact do anything at all) in practice, you can even
>> configure stuff that is in the manual, and is supposed to work, but still
>> doesn't work ;)
>>
>> I turned on flow on a couple of interfaces, turned on top-talkers and got
>> nothing.  I then setup netcat to listen to a UDP port, configured export
>> to send it, and according to show ip flow export it's not exporting
>> anything.
>>
>> It also doesn't bode well for the support that ip flow-export is in the
>> list of unsupported commands in the configuration guide, nor does the fact
>> that there is only one reference to wccp in the configuration guide and
>> that's under the traffic-classifier for the CPU traffic...
>>
>> Kind regards,
>> Sibbi
>>
>> Þann 27.7.2011 21:31, skrifaði "Jason Lixfeld"<jason at lixfeld.ca>:
>>
>>> On 2011-07-27, at 4:45 PM, Colby Glass wrote:
>>>
>>>> All,
>>>>
>>>> Does anyone happen to know if the ME3600 supports Netflow and WCCP? I
>>>> have a
>>>> customer considering them for the WAN edge and the docs/feature
>>>> navigator
>>>> are coming up somewhat ambiguous.
>>>
>>> I haven't tested it, but...
>>>
>>> systems02.151front71(config)#ip flow-?
>>> flow-aggregation  flow-cache        flow-capture  flow-egress
>>> flow-export       flow-top-talkers
>>>
>>> systems02.151front71(config)#ip flow-export ?
>>>   destination  Specify the Destination IP address
>>>   source       Specify the interface for source address
>>>   template     Specify the template specific configurations
>>>   version      Specify the version number
>>>
>>> systems02.151front71(config)#ip flow-export version ?
>>>   1
>>>   5
>>>   9
>>>
>>> systems02.151front71(config)#int g0/1
>>> systems02.151front71(config-if)#no switchport
>>> systems02.151front71(config-if)#ip route-cache ?
>>>   cef             Enable Cisco Express Forwarding
>>>   flow            Enable Flow fast-switching cache
>>>   policy          Enable fast-switching policy cache for outgoing packets
>>>   same-interface  Enable fast-switching on the same interface
>>>   <cr>
>>>
>>> systems02.151front71(config-if)#ip wccp ?
>>>   <0-254>     Dynamically defined service identifier number
>>>   redirect   Set packet redirection options
>>>   web-cache  Standard web caching service
>>>
>>> systems02.151front71(config-if)#
>>>
>>> This is on 12.2(52)EY1
>>> _______________________________________________
>>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>>
>
>