[c-nsp] me3600 svi's not showing in and out bit counts that i see on corresponding phy int

[Xu Hu]

Try to set the load-interval to 30s, then check again.

Thanks and regards,
Xu Hu

On 8 Aug, 2012, at 21:54, "Aaron" <aaron1 at gvtc.com> wrote:

> anybody know why me3600 svi doesn't seem to show in and out bit counts that
> the underlying phy int shows?  ....all svi's (10,11,13) are in a vrf running
> over mpls l3vpn
> 
> 
> 
> 
> 
> 3600#sh int vl 10 | in 30 sec
> 
> 30 second input rate 2000 bits/sec, 3 packets/sec
> 
> 30 second output rate 1000 bits/sec, 3 packets/sec
> 
> 
> 
> 3600#sh int g0/1 | in 30 sec
> 
> 30 second input rate 402000 bits/sec, 359 packets/sec
> 
> 30 second output rate 6157000 bits/sec, 613 packets/sec
> 
> 
> 
> 
> 
> Details.
> 
> 
> 
> 3600>sh ver | in IOS
> 
> Cisco IOS Software, ME360x Software (ME360x-UNIVERSAL-M), Version 15.2(2)S,
> RELEASE SOFTWARE (fc1)
> 
> 
> 
> 3600>sh spann in g0/1
> 
> 
> 
> Vlan                Role Sts Cost      Prio.Nbr Type
> 
> ------------------- ---- --- --------- --------
> --------------------------------
> 
> VLAN0010            Desg FWD 4         128.1    P2p
> 
> VLAN0011            Desg FWD 4         128.1    P2p
> 
> VLAN0012            Desg FWD 4         128.1    P2p
> 
> VLAN0013            Desg FWD 4         128.1    P2p
> 
> 
> 
> 3600>sh int g0/1 | in 30 sec
> 
>  30 second input rate 545000 bits/sec, 459 packets/sec
> 
>  30 second output rate 14636000 bits/sec, 1318 packets/sec
> 
> 
> 
> 3600>sh int vla 10 | in 30 sec
> 
>  30 second input rate 2000 bits/sec, 4 packets/sec
> 
>  30 second output rate 2000 bits/sec, 4 packets/sec
> 
> 
> 
> 3600>sh int vla 11 | in 30 sec
> 
>  30 second input rate 0 bits/sec, 0 packets/sec
> 
>  30 second output rate 0 bits/sec, 0 packets/sec
> 
> 
> 
> 3600>sh int vla 12 | in 30 sec
> 
>                       ^
> 
> % Invalid input detected at '^' marker.
> 
> 
> 
> 3600>sh int vla 13 | in 30 sec
> 
>  30 second input rate 0 bits/sec, 0 packets/sec
> 
>  30 second output rate 0 bits/sec, 0 packets/sec
> 
> 
> 
> 3600>sh spann vl 12
> 
> 
> 
> VLAN0012
> 
>  Spanning tree enabled protocol rstp
> 
>  Root ID    Priority    24588
> 
>             Address     f47f.3549.dd80
> 
>             This bridge is the root
> 
>             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
> 
> 
> 
>  Bridge ID  Priority    24588  (priority 24576 sys-id-ext 12)
> 
>             Address     f47f.3549.dd80
> 
>             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
> 
>             Aging Time 300
> 
> 
> 
> Interface           Role Sts Cost      Prio.Nbr Type
> 
> ------------------- ---- --- --------- --------
> --------------------------------
> 
> Gi0/1               Desg FWD 4         128.1    P2p
> 
> 
> 
> 
> 
> 
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/