[c-nsp] asr901 - vlan-based eompls (l2vpn) supported ?

[George Giannousopoulos]

Hi Aaron,

You aren't doing anything wrong..
SVI based EoMPLS isn't supported on ASR901 yet

It is expected in Q1 2013..

Cheers
George

On Thu, Aug 23, 2012 at 4:49 PM, Aaron <aaron1 at gvtc.com> wrote:

> does vlan-based eompls l2vpn work on asr901 ?  ...in 15.1(2)SNH ?  i can't
> get it to work using the following config...am i doing something wrong ?
>
>
>
> 901#sh ver | in IOS
>
> Cisco IOS Software, 901 Software (ASR901-UNIVERSALK9-M), Version
> 15.1(2)SNH,
> RELEASE SOFTWARE (fc2)
>
>
>
> 901#conf t
>
> Enter configuration commands, one per line.  End with CNTL/Z.
>
> 901(config)#int vl 20
>
> 901(config-if)#xconnect 1.1.0.3 20 encapsulation mpls
>
> The Vl20 a vlan interface - command rejected.
>
>
>
> 901(config-if)#xconnect 1.1.1.1 ?
>
>   <1-4294967295>  Enter VC ID value
>
>
>
> 901(config-if)#xconnect 1.1.1.1 20 ?
>
>   encapsulation  Data encapsulation method
>
>   pw-class       Pseudowire-class to use for encapsulation and protocol
> configuration
>
>
>
> 901(config-if)#xconnect 1.1.1.1 20 encapsulation ?
>
>   l2tpv3  Use L2TPv3 encapsulation
>
>   mpls    Use MPLS encapsulation
>
>
>
> 901(config-if)#xconnect 1.1.1.1 20 encapsulation mpls ?
>
>   manual    Manually configure MPLS session parameters
>
>   pw-class  Optional pseudowire-class to use for advanced configuration
>
>   <cr>
>
>
>
> 901(config-if)#xconnect 1.1.1.1 20 encapsulation mpls
>
> The Vl20 a vlan interface - command rejected.
>
> 901(config-if)#
>
>
>
>
>
>
>
> *****************************************
>
> **** PORT-BASED is working.
>
> *****************************************
>
>
>
> 901#sh run in g0/3
>
> Building configuration...
>
>
>
> Current configuration : 170 bytes
>
> !
>
> interface GigabitEthernet0/3
>
> no negotiation auto
>
> service instance 1 ethernet
>
>   encapsulation untagged
>
>   xconnect 1.1.0.3 20 encapsulation mpls
>
>    mtu 1500
>
> !
>
> end
>
>
>
> 901#sh xcon
>
> 901#sh xconnect all | in 0/3
>
> UP     ac   Gi0/3:1(Ethernet)            UP mpls 1.1.0.3:20
> UP
>
> 901#
>
>
>
>
>
> *****************************************
>
> *** VLAN-BASED is working on my me3600...
>
> *****************************************
>
>
>
>
>
> 3600#sh run in vl 12
>
> Building configuration...
>
>
>
> Current configuration : 123 bytes
>
> !
>
> interface Vlan12
>
> ip address 1.1.5.10 255.255.255.0
>
> load-interval 30
>
> xconnect 1.2.0.2 312 encapsulation mpls
>
> end
>
>
>
>
>
> 3600#sh xconnect all
>
> Legend:    XC ST=Xconnect State  S1=Segment1 State  S2=Segment2 State
>
>   UP=Up       DN=Down            AD=Admin Down      IA=Inactive
>
>   SB=Standby  HS=Hot Standby     RV=Recovering      NH=No Hardware
>
>
>
> XC ST  Segment 1                         S1 Segment 2
> S2
>
>
> ------+---------------------------------+--+--------------------------------
> -+--
>
> UP pri   ac Vl12:12(Eth VLAN)            UP mpls 1.2.0.2:312
> UP
>
>
>
>
>
> 3600#sh ver | in IOS
>
> Cisco IOS Software, ME360x Software (ME360x-UNIVERSALK9-M), Version
> 15.2(2)S, RELEASE SOFTWARE (fc1)
>
> 3600#
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>