[c-nsp] EoMPLS with WS-X6724 and WS-X6704-10GE

[Florin Veres]

Do you have the route for the remote IP in your routing table?
Also, do you have the network MPLS-enabled?

I know these sound like silly questions, but:
  Destination address: 10.100.100.23, VC ID: 777, VC status: down
    Output interface: if-?(0), imposed label stack {}
    Preferred path: not configured
    Default path: no route
    No adjacency

Also, there seems to be a issue with targeted LDP:
  Create time: 00:20:49, last status change time: 00:00:00
  Signaling protocol: LDP, peer 10.100.100.23:0 up
    Targeted Hello: 10.100.100.4(LDP Id) -> 10.100.100.23
    MPLS VC labels: local 456, remote unassigned
    Group ID: local 0, remote unknown
    MTU: local 1500, remote unknown


On Wed, Oct 31, 2012 at 9:55 AM, zaid <zaidoon_h at yahoo.com> wrote:

> hi
>
> I tried with port based but i get the same result , and for subinterface I
> wont go with it
> here is the output
>
> sh mpls l2transport vc 777 detail
> Local interface: Vl666 up, line protocol up, Eth VLAN 666 up
>   MPLS VC type is Eth VLAN, interworking type is Ethernet
>   Destination address: 10.100.100.23, VC ID: 777, VC status: down
>     Output interface: if-?(0), imposed label stack {}
>     Preferred path: not configured
>     Default path: no route
>     No adjacency
>   Create time: 00:20:49, last status change time: 00:00:00
>   Signaling protocol: LDP, peer 10.100.100.23:0 up
>     Targeted Hello: 10.100.100.4(LDP Id) -> 10.100.100.23
>     MPLS VC labels: local 456, remote unassigned
>     Group ID: local 0, remote unknown
>     MTU: local 1500, remote unknown
>     Remote interface description:
>   Sequencing: receive disabled, send disabled
>   VC statistics:
>     packet totals: receive 0, send 0
>     byte totals:   receive 0, send 0
>     packet drops:  receive 0, send 0
>
> I followed the config from this link :
>
>
> http://www.cisco.com/en/US/docs/ios/12_1/12_1ex/feature/guide/eompls9.html#wp1119431
>
> thanks
>
>
> ________________________________
>  From: zaid <zaidoon_h at yahoo.com>
> To: "cisco-nsp at puck.nether.net" <cisco-nsp at puck.nether.net>
> Sent: Wednesday, October 31, 2012 9:12 AM
> Subject: EoMPLS with WS-X6724 and WS-X6704-10GE
>
>
> Hi
>
> I can't  deploy EoMpls between two routers7600 (R1 WS-X6724 facing core,R2
> WS-X6704-10GE facing core) while  between two routers (WS-X6724 facing
> core) the PW is up and running , is there any HW restrictions .
>
> Regards
>
> Zaid
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>