[c-nsp] 802.1Q-in-Q VLAN Tag Termination on 7600/6500 OSN modules

[Davide Ambrosi]

Hello Mattias,
but in the ME3600X (or ME3800X) is it possible to apply a
configuration like this ?

interface gigabitethernet0/1.10100
no switchport
encapsulation dot1q 10 second-dotq 100
ip address 10.0.0.1 255.255.255.0


with the ES+ (and I think also with 7600-SIP-400 + SPA-5X1GE-V2) is possible.

Thanks,
Davide

2013/2/28 Mattias Gyllenvarg <Mattias.Gyllenvarg at bredband2.se>:
> Do it in the 3600X, thats what there good at.
>
>
> On 28 February 2013 09:55, Davide Ambrosi <davide.ambrosi at trivenet.it>
> wrote:
>>
>> Thanks Mack,
>> so I have to change all the 7603 boxes and move to 7603-S to support
>> the ES+ cards and upgrade all the supervisors to SUP720-3B minimum.
>> Moving to ASR's series (like the ASR1002) could be a good alternative
>> choice because of the limited GE ports I need on the small POP's (5
>> GE) ?
>>
>> Davide
>>
>>
>> 2013/2/27 Mack McBride <mack.mcbride at viawest.com>:
>> > The ES+ cards are the way to go.
>> > The OSM modules aren't going to do what you want.
>> > In addition they aren't properly supported in newer code.
>> >
>> > LR Mack McBride
>> > Network Architect
>> >
>> > -----Original Message-----
>> > From: cisco-nsp-bounces at puck.nether.net
>> > [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Davide Ambrosi
>> > Sent: Wednesday, February 27, 2013 9:32 AM
>> > To: cisco-nsp at puck.nether.net
>> > Subject: [c-nsp] 802.1Q-in-Q VLAN Tag Termination on 7600/6500 OSN
>> > modules
>> >
>> > Hello,
>> >
>> > We have some 7603 boxes with SUP720/SUP2 installed as main supervisor in
>> > our MPLS Edge sites.
>> >
>> > Now we need to terminate QinQ VLAN directly on one or more GE interfaces
>> > of the 7603 routers because we are planning to introduce metro ethernet
>> > tecnologies (ME3400E/ME3600X) in our fiber and microwave access network for
>> > reducing the VLAN configured between the switches located in the access
>> > network (now we have 1 VLAN = 1 Customer).
>> >
>> > I see that 7600 catalyst modules doesn't support QinQ VLAN termination
>> > (the command "encapsulation dot1q outer-vlan second-dot1q inner-vlan)
>> > because they are "LAN" modules.
>> >
>> > Is there anyone who tested QinQ termination on old 7600 OSN GE modules
>> > like the OSM-2+4GE-WAN+ ? If not supported the only way to support QinQ is
>> > to buy new (expensive) 7600-S chassis + ES cards or SIP-400 and SPAs V2 ?
>> >
>> > In out network environment we have also some 7609-S(RSP720) with ES+
>> > card located into the core an large aggregation sites and with this
>> > equipment we don't have problems because the QinQ Termination is supported
>> > on ES+ card.
>> >
>> >
>> > Davide
>> > _______________________________________________
>> > cisco-nsp mailing list  cisco-nsp at puck.nether.net
>> > https://puck.nether.net/mailman/listinfo/cisco-nsp
>> > archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>> _______________________________________________
>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
>
>
>
> --
> *Med Vänliga Hälsningar - Best Regards*
>
> *Mattias Gyllenvarg*
> *Nätutveckling*
> Bredband2
>
> Tel: +46 406219712
>