[c-nsp] ME-3600 Can't see ip pim vrf neighbor

[Fredrik Vöcks]

Read what Claes said.

You must change SDM to applications.

Fredrik Vöcks
Senior IP Network Engineer



On 23 May 2013 15:09, PlaWanSai <pws_admin at thaicpe.com> wrote:

> I enabled on loopback 0. And I see this log on first boot:
>
> 000038: *May 22 16:28:50.879 BKK: NQATM:
> 000039: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000040: *May 22 16:28:50.879 BKK: NQATM:
> 000041: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000042: *May 22 16:28:50.879 BKK: NQATM:
> 000043: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000044: *May 22 16:28:50.879 BKK: NQATM:
> 000045: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000046: *May 22 16:28:50.879 BKK: NQATM:
> 000047: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000048: *May 22 16:28:50.879 BKK: NQATM:
> 000049: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000050: *May 22 16:28:50.879 BKK: NQATM:
> 000051: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000052: *May 22 16:28:50.879 BKK: NQATM:
> 000053: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000054: *May 22 16:28:50.879 BKK: NQATM:
> 000055: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
> 000056: *May 22 16:28:50.879 BKK: NQATM:
> 000057: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate
> tcam hw handle
>
> Thank you very much.
>
> -----Original Message-----
> From: Claes Jansson [mailto:claes at gastabud.com]
> Sent: Thursday, May 23, 2013 7:34 PM
> To: PlaWanSai
> Cc: cisco-nsp at puck.nether.net
> Subject: Re: [c-nsp] ME-3600 Can't see ip pim vrf neighbor
>
> Also be sure to use
>
> ip pim ssm default
>
> and
>
> sdm prefer applications
>
> By default "MDT mroutes" are 0...
>
> I have tested this on 15.3(2)S.
>
> Claes Jansson
> Gästabudstaden AB
>
> On 2013-05-23 08:38, PlaWanSai wrote:
> > I try to run Multicast VPN on the ME-3600 back-to-back with the 7609.
> > It does not see pim neighbor. I tested on 15.1(2)EY4, 15.3(1)S and
> > 15.3(2)S IOS version. I used this configuration between 7609 is work.
> >
> >
> >
> > test-co3600#sho ip pim vrf IPTV-M nei
> >
> > PIM Neighbor Table
> >
> > Mode: B - Bidir Capable, DR - Designated Router, N - Default DR
> > Priority,
> >
> >        P - Proxy Capable, S - State Refresh Capable, G - GenID Capable
> >
> > Neighbor          Interface                Uptime/Expires    Ver   DR
> >
> > Address
> Prio/Mode
> >
> > test-co3600#
> >
> >
> >
> > Thank you very much.
> >
> > _______________________________________________
> > cisco-nsp mailing list  cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
> >
>
>
>