[c-nsp] 6500 Supervisor redendancy

[Edward Salonia]

There ya go. Glad it worked out for you!



On May 29, 2013, at 8:41 PM, "Ben Hammadi, Kayssar (NSN - TN/Tunis)" <kayssar.ben_hammadi at nsn.com> wrote:

> Dears , 
> 
> 
>    I did it successfully tonight , the code on the new Sup was SXJ4 however the code on the running Sup is SXI8a . I just insert the new SUP and it come up with RPR mode so I copy the SXI8 from Sup-bootdisk to the Slavesub-bootdisck and reconfigured the boot to make the path change on the new Sup then reset it and it come to SSO. 
> 
>    The only strange thinks I encounter is that the slot 6 where I inserted the new Sup was disabled but this didn't prevent the Sup to come up with RPR:
> 
> TSA3-PACOSWB9004(config)#no power enable module 6 
> %FRU Absent. Power admin state updated
> TSA3-PACOSWB9004(config)#
> TSA3-PACOSWB9004#
> May 30 00:37:52.248 GMT+1: %PFREDUN-SP-4-VERSION_MISMATCH: Defaulting to RPR mode (Different sw versions)
> May 30 00:37:53.281 GMT+1: %PFREDUN-SP-6-ACTIVE: Standby initializing for RPR mode
> May 30 00:37:54.437 GMT+1: %FABRIC-SP-5-FABRIC_MODULE_BACKUP: The Switch Fabric Module in slot 6 became standby
> May 30 00:37:57.032 GMT+1: %DIAG-SP-6-RUN_MINIMUM: Module 6: Running Minimal Diagnostics...
> May 30 00:37:57.084 GMT+1: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing the startup configuration to the standby Router. 
> May 30 00:38:01.202 GMT+1: %OIR-SP-6-INSCARD: Card inserted in slot 6, interfaces are now online
> May 30 00:38:01.718 GMT+1: %PFREDUN-SP-4-BOOTSTRING_INVALID: The bootfile sup-bootdisk:s72033-advipservicesk9-mz.122-33.SXI8a.bin is present on the active supervisor but not on the standby
> May 30 00:38:02.583 GMT+1: %RF-SP-5-RF_TERMINAL_STATE: Terminal state reached for (RPR)
> TSA3-PACOSWB9004#
> 
> Thanks for your help.
> 
> BEN HAMMADI Kayssar
>  
> NOKIA SIEMENS NETWORKS
> Lead Engineer -BroadBand Connectivity
> JNCIE-M (#471), JNCIE-SP (#1147), CCIP 
> Mobile : +216 29 349 952  /  +216 98 349 952
> FIX      : +216 71 108 173
> Skype : kayssar ben hammadi
> kayssar.ben_hammadi at nsn.com
> 
> 
> -----Original Message-----
> From: ext Edward Salonia [mailto:ed at edgeoc.net] 
> Sent: Wednesday, May 29, 2013 4:28 PM
> To: Ben Hammadi, Kayssar (NSN - TN/Tunis)
> Cc: ext Justin M. Streiner; cisco-nsp at puck.nether.net
> Subject: Re: [c-nsp] 6500 Supervisor redendancy
> 
> While your mileage may vary I have has great success in doing this exact thing. RMA sups don't necessarily come with the same code as what you are running. Put the new sup in (same hardware, right?) and it should boot up into RPR standby cold due to the mid matched code. At this point copy the code from the flash of one sup to the other 'wr mem', check 'show red' to ensure config reg and boot var are correct and a 'redundancy reload peer' should do the trick.
> 
> Out of curiosity, what code are you running on this?
> 
> Also is your box configured for SSO mode currently and is running in simplex, or is it configured for RPR. If the latter, I think it may require a reload to change modes, but I don't recall.
> 
> Good luck.
> 
> - Ed
> 
> 
> On May 28, 2013, at 5:10 PM, "Ben Hammadi, Kayssar (NSN - TN/Tunis)" <kayssar.ben_hammadi at nsn.com> wrote:
> 
>> Hi, 
>> 
>>  My major concern is about the IOS difference , should I find a way to check what is the IOS on the new Supervisor or this will not make difference , I read the successful stories in Cisco websites but here I am asking people who really did that on live Switchs. 
>> 
>> Br.
>> 
>> BEN HAMMADI Kayssar
>> 
>> NOKIA SIEMENS NETWORKS
>> Lead Engineer -BroadBand Connectivity
>> JNCIE-M (#471), JNCIE-SP (#1147), CCIP 
>> 
>> 
>> -----Original Message-----
>> From: cisco-nsp [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of ext Justin M. Streiner
>> Sent: Tuesday, May 28, 2013 9:58 PM
>> To: cisco-nsp at puck.nether.net
>> Subject: Re: [c-nsp] 6500 Supervisor redendancy
>> 
>> On Tue, 28 May 2013, Ben Hammadi, Kayssar (NSN - TN/Tunis) wrote:
>> 
>>> I have a 6509 with a standalone Sup720 and I am preparing to add a 
>>> redundant one, I don't know the software on the new Supervisor and my 
>>> final goal is to make both work on SSO mode. Can someone propose a 
>>> procedure with happy end :) ?
>> 
>> There are numerous resources online that talk about how to configure dual 
>> supervisors in a Cat6500 switch.
>> 
>> You might be better off asking specific questions, based on things you've
>> tried or read through, rather than asking other people to do the majority 
>> of the work for you.
>> 
>> jms
>> _______________________________________________
>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>> 
>> _______________________________________________
>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/