[c-nsp] SPA issue on ASR1006
Jordi Magrané Roig
jordimagrane at hotmail.com
Wed Apr 22 11:01:32 EDT 2015
Dear Edward,
Thanks for your e-mail. This SIP has other SPA running fine.
I inserted again the SPA to the SIP and I received the following log:
Apr 22
14:18:13: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 1/2
Apr 22
14:18:21: %LINK-3-UPDOWN: SIP1/2: Interface EOBC1/1, changed state to up
Apr 22
14:18:24: %IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet1/2/0, link down due
to local fault
Apr 22 14:18:24:
%SPA_OIR-6-ONLINECARD: SPA (SPA-1X10GE-L-V2) online in subslot 1/2
Apr 22 14:18:26: %CMCC-3-PLIM_STATUS: SIP1:
cmcc: A PLIM driver informational error
TXSPI2 Frame Error, block 19 count 1
Apr 22
14:20:52: %IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet1/2/0, link down due
to local fault
Apr 22
14:20:54: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/2/0, changed state to
down
Apr 22
14:20:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface
TenGigabitEthernet1/2/0, changed state to down
Apr 22
14:20:54: %LINK-3-UPDOWN: SIP1/2: Interface TenGigabitEthernet1/2/0, changed
state to down
Do you know what is the meaning of the PLM driver message?
Are there commands that I could executed to check that the SPA is working fine?
I inserted an SPF and made a loop and the port went UP:
Apr 22
14:25:27: %TRANSCEIVER-6-INSERTED: SIP1/2: transceiver module inserted in
TenGigabitEthernet1/2/0
Apr 22
14:25:30: %IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet1/2/0, link down due
to local fault
Apr 22
14:25:40: %TRANSCEIVER-6-REMOVED: SIP1/2: Transceiver module removed from
TenGigabitEthernet1/2/0
Apr 22
14:26:10: %TRANSCEIVER-6-INSERTED: SIP1/2: transceiver module inserted in
TenGigabitEthernet1/2/0
Apr 22
14:26:13: %IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet1/2/0, link down due
to local fault
Apr 22
14:29:41: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/2/0, changed state to
up
Apr 22
14:29:42: %LINEPROTO-5-UPDOWN: Line protocol on Interface
TenGigabitEthernet1/2/0, changed state to up
Apr 22
14:29:41: %LINK-3-UPDOWN: SIP1/2: Interface TenGigabitEthernet1/2/0, changed
state to up
ASR1006-LIS01-02#sh
platform
Chassis type:
ASR1006
Slot Type State Insert time (ago)
---------
------------------- --------------------- -----------------
0 ASR1000-SIP10 ok 13w5d
0/0
SPA-5X1GE-V2 ok 13w5d
0/1
SPA-4XOC3-POS ok 13w5d
0/2
SPA-1XOC12-POS ok 13w5d
0/3
SPA-4XOC3-POS ok 13w5d
1 ASR1000-SIP10 ok 13w5d
1/0
SPA-5X1GE-V2 ok 13w5d
1/1
SPA-4XOC3-POS ok 13w5d
1/2 SPA-1X10GE-L-V2 ok 00:34:16
1/3
SPA-4XOC12-POS ok 13w5d
R0 ASR1000-RP2 ok, active 13w5d
R1 ASR1000-RP2 ok, standby 13w5d
F0 ASR1000-ESP20 ok, active 13w5d
F1 ASR1000-ESP20 ok, standby 13w5d
P0 ASR1006-PWR-AC ok 13w5d
P1 ASR1006-PWR-AC ok 13w5d
Slot CPLD Version Firmware Version
---------
------------------- ---------------------------------------
0 09111601 12.2(33r)XNC
1 09111601 12.2(33r)XNC
R0 10021901 12.2(33r)XND
R1 10021901 12.2(33r)XND
F0 08041102 12.2(33r)XNC
F1 08041102 12.2(33r)XNC
ASR1006-LIS01-02#sh
int te1/2/0
TenGigabitEthernet1/2/0
is up, line protocol is up
Hardware is SPA-1X10GE-L-V2, address is
a493.4c76.4260 (bia a493.4c76.4260)
MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10
usec,
reliability 255/255, txload 1/255, rxload
1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
Full Duplex, 10000Mbps, link type is
force-up, media type is 10GBase-LR
output flow-control is on, input flow-control
is on
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:01:58, output 00:01:58, output
hang never
Last clearing of "show interface"
counters never
Input queue: 0/375/0/0
(size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 0 bits/sec, 0
packets/sec
30 second output rate 0 bits/sec, 0
packets/sec
1 packets input, 60 bytes, 0 no buffer
Received 1 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun,
0 ignored
0 watchdog, 0 multicast, 0 pause input
1 packets output, 60 bytes, 0 underruns
0 output errors, 0 collisions, 5 interface
resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause
output
0 output buffer failures, 0 output buffers
swapped out
ASR1006-LIS01-02#sh
hw-module subslot 1/2 transceiver 0 idprom detai
IDPROM for
transceiver TenGigabitEthernet1/2/0:
Description = XFP optics
(type 6)
Transceiver Type: = OC192 + 10GBASE-L
(97)
Product Identifier (PID) = XFP-10GLR-OC192SR
Vendor Revision = B2
Serial Number (SN) = AGA1125N1X9
Vendor Name =
CISCO-AVAGO
Vendor OUI (IEEE company ID) = 00.17.6A (5994)
CLEI code = WMOTBEVAAB
Cisco part number = 10-1989-02
Device State = Enabled.
Date code (yy/mm/dd) = 07/07/22
Connector type = LC.
Encoding = 64B/66B
SONET Scrambled
NRZ
Minimum bit rate = 9900 Mbits/s
Maximum bit rate = 10500 Mbits/s
Power dissipation class = Pwr Level 2 (2.5 W max pwr
dissipation).
cdr function = supported.
Tx Reference clock = not Required.
Max link length for SMF fiber = 10 km
Max link length for EBW 50/125um fiber = not supported
Max link length for 0/125um fiber = not supported
Max link length for 62.5/125um fiber = not supported
Max link length for copper = not supported
Tx device technology = 1550 nm DFB
Wavelength control technology = no wavelength control
Transceiver cooling technology = un-cooled transmitter device
Detector type = PIN detector
Transmitter tuning = transmitter not
tunable
Supported CDR rates = 9.95 Gb/s
10.3 Gb/s
10.5 Gb/s
XFI Loopback Mode
Nominal laser wavelength = 1310 nm
Wavelength tolerance w.r.t. nominal = (+/-) 20 nm
Maximum case temperature = 70 degrees C.
Maximum power dissipation = 2500 mW
Power dissipation in power-down mode = 1500 mW
Maximum current required for +5V supply = 0 mA
Maximum current required for +3.3V supply =
800 mA
Maximum current required for +1.8V supply = 0
mA
Maximum current required for -5.2V supply = 0
mA
Diagnostic capabilities = FEC BER not supported.
average Rx power measured.
Enhanced functions = Soft TX disable
supported
Soft Power-down supported
Aux A/D input 1 = Laser Temperature
Aux A/D input 2 =
Transceiver temperature operating range = -5 C to 75 C (commercial)
High temperature alarm threshold = +78.000 C
High temperature warning threshold = +73.000 C
Low temperature warning threshold = +5.000 C
Low temperature alarm threshold = +0.000 C
High laser bias current alarm threshold = 100.000 mAmps
High laser bias current warning threshold =
85.000 mAmps
Low laser bias current warning threshold = 15.000 mAmps
Low laser bias current alarm threshold = 5.000 mAmps
High transmit power alarm threshold =
3.5 dBm
High transmit power warning threshold =
1.5 dBm
Low transmit power warning threshold = -9.2 dBm
Low transmit power alarm threshold = -11.2 dBm
High receive power alarm threshold =
3.5 dBm
High receive power warning threshold =
1.5 dBm
Low receive power warning threshold = -15.4 dBm
Low receive power alarm threshold = -17.4 dBm
Thanks.
> Subject: Re: [c-nsp] SPA issue on ASR1006
> From: ed at edgeoc.net
> Date: Wed, 22 Apr 2015 08:16:55 -0400
> CC: cisco-nsp at puck.nether.net
> To: jordimagrane at hotmail.com
>
> Bad SPA or bad SIP. Try moving the SPA to a different slot in the SIP. If it comes up that could point to the original slot as faulty. If it doesn't help it could be a bad SPA.
>
> - Ed
>
>
>
> On Apr 22, 2015, at 07:27, Jordi Magrané Roig <jordimagrane at hotmail.com> wrote:
>
> Dear colleagues,
>
> I have an ASR1006 with ESP20, RP2 and two SIP10. Recently I have inserted one SPA 1x10G into one of the SIP10 and I have seen the following log messages:
>
>
>
> Apr 22 12:00:53: %IOSXE_OIR-6-INSSPA: SPA inserted in
> subslot 1/2
>
> Apr 22 12:01:00: %LINK-3-UPDOWN: SIP1/2: Interface
> EOBC1/1, changed state to up
>
> ASR1006-LIS01-02#sh ip int
>
> Apr 22 12:01:03: %IOSXE_SPA-6-UPDOWN: Interface
> TenGigabitEthernet1/2/0, link down due to local fault
>
> Apr 22 12:01:03: %SPA_OIR-6-ONLINECARD: SPA
> (SPA-1X10GE-L-V2) online in subslot 1/2
>
> Apr 22 12:01:11: %IOSXE_SIP_SPA-4-SPABUS: SIP1/2:
> Subslot 2, Read SPA BUS access failed. timeout=0 err=1 par=0 err_c=0x10883
> addr=0x00045008 data =0x0
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:12: %IOSXE_SIP_SPA-3-DEVICE_ERROR:
> SIP1/2: subSlot 2, spatype 0x50C. Device error: critical fault occured
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:15: %CMCC-3-PLIM_STATUS: SIP1:
> cmcc: A PLIM driver informational error RXSPI2 Out of Frame, block 15
> count 3
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:17: %SPA_OIR-3-RECOVERY_RELOAD: subslot
> 1/2: Attempting recovery by reloading SPA
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:17: %SPA_OIR-6-OFFLINECARD: SPA
> (SPA-1X10GE-L-V2) offline in subslot 1/2
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:26: %IOSXE_SIP_SPA-3-SPI4_NOTSYNC:
> SIP1/2: SPA-1X10GE-L-V2[1/2]: Can not synchronize SPI4 bus (host: src in sync,
> sink not in sync, spa: src in sync, sink not in sync).
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:31: %SPA_OIR-3-RECOVERY_RELOAD: subslot
> 1/2: Attempting recovery by reloading SPA
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:31: %SPA_OIR-6-OFFLINECARD: SPA
> (SPA-1X10GE-L-V2) offline in subslot 1/2
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:39: %IOSXE_SIP_SPA-3-SPI4_NOTSYNC:
> SIP1/2: SPA-1X10GE-L-V2[1/2]: Can not synchronize SPI4 bus (host: src in sync,
> sink not in sync, spa: src in sync, sink not in sync).
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:44: %SPA_OIR-3-RECOVERY_RELOAD: subslot
> 1/2: Attempting recovery by reloading SPA
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:44: %SPA_OIR-6-OFFLINECARD: SPA
> (SPA-1X10GE-L-V2) offline in subslot 1/2
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:52: %IOSXE_SIP_SPA-3-SPI4_NOTSYNC:
> SIP1/2: SPA-1X10GE-L-V2[1/2]: Can not synchronize SPI4 bus (host: src in sync,
> sink not in sync, spa: src in sync, sink not in sync).
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:57: %SPA_OIR-3-RECOVERY_RELOAD: subslot
> 1/2: Attempting recovery by reloading SPA
>
> ASR1006-LIS01-02#
>
> Apr 22 12:01:57: %SPA_OIR-6-OFFLINECARD: SPA
> (SPA-1X10GE-L-V2) offline in subslot 1/2
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> Apr 22 12:02:05: %IOSXE_SIP_SPA-3-SPI4_NOTSYNC:
> SIP1/2: SPA-1X10GE-L-V2[1/2]: Can not synchronize SPI4 bus (host: src in sync,
> sink not in sync, spa: src in sync, sink not in sync).
>
> ASR1006-LIS01-02#
>
> Apr 22 12:02:10: %SPA_OIR-3-RECOVERY_RELOAD: subslot
> 1/2: Attempting recovery by reloading SPA
>
> ASR1006-LIS01-02#
>
> Apr 22 12:02:10: %SPA_OIR-6-OFFLINECARD: SPA
> (SPA-1X10GE-L-V2) offline in subslot 1/2
>
> ASR1006-LIS01-02#
>
> Apr 22 12:02:18: %SPA_OIR-3-SPA_POWERED_OFF: subslot
> 1/2: SPA 1x10GE XFP SPA powered off after 5 failures within 1200 seconds
>
> ASR1006-LIS01-02#
>
> Apr 22 12:02:18: %SPA_OIR-6-OFFLINECARD: SPA
> (SPA-1X10GE-L-V2) offline in subslot 1/2
>
> ASR1006-LIS01-02#
>
> Apr 22 12:02:18: %IOSXE_SIP_SPA-3-SPI4_NOTSYNC:
> SIP1/2: SPA-1X10GE-L-V2[1/2]: Can not synchronize SPI4 bus (host: src in sync,
> sink not in sync, spa: src in sync, sink not in sync).
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> ASR1006-LIS01-02#
>
> Apr 22 12:02:47: %IOSXE_OIR-6-REMSPA: SPA removed from
> subslot 1/2, interfaces disabled
>
>
>
> Any ideas about this issue?
>
>
>
> ASR1006-LIS01-02#sh platform
>
> Chassis type:
> ASR1006
>
>
>
>
> Slot
> Type
> State
> Insert time (ago)
>
> --------- ------------------- ---------------------
> -----------------
>
> 0
> ASR1000-SIP10
> ok
> 13w5d
>
> 0/0
> SPA-5X1GE-V2
> ok
> 13w5d
>
> 0/1
> SPA-4XOC3-POS
> ok
> 13w5d
>
> 0/2
> SPA-1XOC12-POS
> ok
> 13w5d
>
> 0/3
> SPA-4XOC3-POS
> ok
> 13w5d
>
> 1
> ASR1000-SIP10
> ok
> 13w5d
>
> 1/0
> SPA-5X1GE-V2
> ok
> 13w5d
>
> 1/1
> SPA-4XOC3-POS
> ok
> 13w5d
>
> 1/2
> SPA-1X10GE-L-V2
> booting
> 00:00:01
>
> 1/3
> SPA-4XOC12-POS
> ok
> 13w5d
>
> R0
> ASR1000-RP2 ok, active
> 13w5d
>
> R1
> ASR1000-RP2 ok,
> standby
> 13w5d
>
> F0
> ASR1000-ESP20 ok,
> active
> 13w5d
>
> F1
> ASR1000-ESP20 ok,
> standby
> 13w5d
>
> P0
> ASR1006-PWR-AC ok
> 13w5d
>
> P1
> ASR1006-PWR-AC
> ok
> 13w5d
>
>
>
> Slot CPLD
> Version Firmware
> Version
>
>
> --------- -------------------
> ---------------------------------------
>
> 0 09111601
> 12.2(33r)XNC
>
>
> 1
> 09111601
> 12.2(33r)XNC
>
>
> R0
> 10021901
> 12.2(33r)XND
>
>
> R1
> 10021901
> 12.2(33r)XND
>
>
> F0
> 08041102
> 12.2(33r)XNC
>
>
> F1
> 08041102
> 12.2(33r)XNC
>
>
>
>
> ASR1006-LIS01-02#
>
>
> ASR1006-LIS01-02#sh ver
> Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.2(4)S6, RELEASE SOFTWARE (fc4)
> Technical Support: http://www.cisco.com/techsupport
> Copyright (c) 1986-2014 by Cisco Systems, Inc.
> Compiled Thu 14-Aug-14 19:30 by mcpre
>
> IOS XE Version: 03.07.06.S
>
> Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.
> All rights reserved. Certain components of Cisco IOS-XE software are
> licensed under the GNU General Public License ("GPL") Version 2.0. The
> software code licensed under GPL Version 2.0 is free software that comes
> with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
> GPL code under the terms of GPL Version 2.0. For more details, see the
> documentation or "License Notice" file accompanying the IOS-XE software,
> or the applicable URL provided on the flyer accompanying the IOS-XE
> software.
>
>
> ROM: IOS-XE ROMMON
>
> ASR1006-LIS01-02 uptime is 13 weeks, 5 days, 11 hours, 5 minutes
> Uptime for this control processor is 13 weeks, 5 days, 11 hours, 6 minutes
> System returned to ROM by reload at 00:18:14 CET Fri Jan 16 2015
> System restarted at 00:21:28 CET Fri Jan 16 2015
> System image file is "bootflash:asr1000rp2-advipservicesk9.03.07.06.S.152-4.S6.bin"
> Last reload reason: Reload Command
>
>
>
> This product contains cryptographic features and is subject to United
> States and local country laws governing import, export, transfer and
> use. Delivery of Cisco cryptographic products does not imply
> third-party authority to import, export, distribute or use encryption.
> Importers, exporters, distributors and users are responsible for
> compliance with U.S. and local country laws. By using this product you
> agree to comply with applicable laws and regulations. If you are unable
> to comply with U.S. and local laws, return this product immediately.
>
> A summary of U.S. laws governing Cisco cryptographic products may be found at:
> http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
>
> If you require further assistance please contact us by sending email to
> export at cisco.com.
>
> cisco ASR1006 (RP2) processor with 4238183K/6147K bytes of memory.
> Processor board ID FOX1608H96D
> 10 Gigabit Ethernet interfaces
> 17 Packet over SONET interfaces
> 32768K bytes of non-volatile configuration memory.
> 8388608K bytes of physical memory.
> 1826815K bytes of eUSB flash at bootflash:.
> 78085207K bytes of SATA hard disk at harddisk:.
>
> Configuration register is 0x2102
>
>
> Thanks in advance for your support.
>
> Best regards,
> Jordi
>
>
>
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
More information about the cisco-nsp
mailing list