[c-nsp] FW: N7K F2e Module

[Sandor Rozsa]

I dag this issue and found out that if you mix M1 with f2e than on the f2e
you'll have only l2 features. You can try by creating an f2e only vdc and
see if the features are available.

sandor

On Wed, Sep 2, 2015 at 12:39 PM, Mohammad Khalil <eng_mssk at hotmail.com>
wrote:

> Please check below
>
> sh vdc
> Switchwide mode is m1 f1 m1xl f2 m2xl f2e
>
> vdc_id  vdc_name                          state               mac
>   type        lc
> ------  --------                          -----               ----------
>   ---------   ------
> 1       JCBank_Core1_DR                   active
> 64:a0:e7:3f:94:41
>   Ethernet    m1 m1xl m2xl f2e
>
> sh vdc feature-set
> vdc JCBank_Core1_DR allowed feature-sets:
>         ethernet
>
> SW(config-if)# interface Ethernet2/19
> SW(config-if)# switchport ?
>   host  Set port host
>
> sh mod
> Mod  Ports  Module-Type                         Model              Status
> ---  -----  ----------------------------------- ------------------
> ----------
> 1    48     10/100/1000 Mbps Ethernet XL Module N7K-M148GT-11L     ok
> 2    32     10 Gbps Ethernet XL Module          N7K-M132XP-12L     ok
> 5    0      Supervisor Module-1X                N7K-SUP1           active *
> 6    0      Supervisor Module-1X                N7K-SUP1
>  ha-standby
> 10   48     1/10 Gbps Ethernet Module           N7K-F248XP-25E     ok
>
> Mod  Sw              Hw
> ---  --------------  ------
> 1    6.2(2a)         1.2
> 2    6.2(2a)         1.3
> 5    6.2(2a)         2.3
> 6    6.2(2a)         2.3
> 10   6.2(2a)         1.2
>
> Thanks in advance
>
> BR,
> Mohammad
> Date: Wed, 2 Sep 2015 11:06:57 +0200
> Subject: Re: [c-nsp] N7K F2e Module
> From: rozsa.sandor.gyula at gmail.com
> To: eng_mssk at hotmail.com
>
> Hi,
> What is the vdc type (limit resources) you are using? I recall I had
> something similar when missconfiguring the vdc type, but in my case I had
> only f2e cards, so the workaround was easy, just modify the module type to
> f2e.
>
> http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus7000/sw/vdc/command/reference/vdc_cmd_ref/vdc_cmds.html
>
> I hope my comment helped you:
> sandor
> On Wed, Sep 2, 2015 at 10:52 AM, Mohammad Khalil <eng_mssk at hotmail.com>
> wrote:
> Hi all
>
> I have Cisco N7K with 6.2.2a  Image
>
> I brought F2e module to be installed on my system and I have already M1xl
> (30 ports fiber module ) already in place
>
> After installing the F2e module , most of the ports on the M1 module
> (which were configured as trunk ports) shows the I cannot configure the
> ports except for host mode
>
>
>
> Switchport mode  host
>
> only
>
>
>
> Anyone faced such a case?
>
>
>
> Thanks in advance
>
>
>
> BR,
>
> Mohammad
>
>
>
> _______________________________________________
>
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>
> https://puck.nether.net/mailman/listinfo/cisco-nsp
>
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
>
>
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>