[c-nsp] IPv4 Multicast (Non-MVPN) MPLS - Single RP for multiple groups

eyeballi77 eyeballi77 at gmail.com
Mon Oct 10 11:17:01 EDT 2016


Hi folks,

..need some help..

I have tried to add add a new group (2) on an existing RP and working setup
used by group 1

Group 1 = 225.10.10.12
Group 2 = 225.10.10.13

Mode = sparse
RP mapping = static with ACL

The group 1 setup is build on VDSL/PPPoE into MPLS with GRE tunnel for
mcast with approx 15 sites working.
The group 2 setup is build on SVTI into MPLS PE to join the same vrf as the
group 1 setup.

The new site that is to use group 2 works fine using group 1 address, but
fails when trying to use the group 2 address.

I have narrowed the issue down to the PE, but wanted to reach out to see if
anyone can give me pointers..

below is the output of mstat for group 1
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mstat 10.32.251.20 225.10.10.12
Type escape sequence to abort.
Mtrace from 10.32.251.20 to 169.254.100.78 via group 225.10.10.12
>From source (?) to destination (?)
Waiting to accumulate statistics......
Results after 10 seconds:

  Source        Response Dest   Packet Statistics For     Only For Traffic
10.32.251.20    169.254.100.78  All Multicast Traffic     From 10.32.251.20
     |       __/  rtt 31   ms   Lost/Sent = Pct  Rate     To 225.10.10.12
     v      /     hop 31   ms   ---------------------
--------------------
10.32.251.253
169.254.32.254  ?
     |     ^      ttl   0
     v     |      hop 3484 ms    2/320 = 1%      32 pps    0/0 = --%  0 pps
169.254.32.253
169.254.100.77  ? Reached RP/Core
     |     ^      ttl   1
     v     |      hop -3   s     -2/318 = --%      31 pps    0/0 = --%  0
pps
169.254.100.78  ?
     |      \__   ttl   2
     v         \  hop 0    ms        0         0 pps           0    0 pps
169.254.100.78  169.254.100.78
  Receiver      Query Source


the same for group 2

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

mstat 10.32.251.20 225.10.10.13
Type escape sequence to abort.
Mtrace from 10.32.251.20 to 169.254.100.78 via group 225.10.10.13
>From source (?) to destination (?)
Waiting to accumulate statistics......
Results after 10 seconds:

  Source        Response Dest   Packet Statistics For     Only For Traffic
0.0.0.0         169.254.100.78  All Multicast Traffic     From 10.32.251.20
     |       __/  rtt 20   ms   Lost/Sent = Pct  Rate     To 225.10.10.13
     v      /     hop 20   ms   ---------------------
--------------------
0.0.0.0
169.254.100.77  ? Reached RP/Core
     |     ^      ttl   0
     v     |      hop 0    ms    -4/324 = --%      32 pps    0/0 = --%  0
pps
169.254.100.78  ?
     |      \__   ttl   1
     v         \  hop 0    ms        0         0 pps           0    0 pps
169.254.100.78  169.254.100.78
  Receiver      Query Source


both groups use the same source server address so while working for group 1
there should be no changes required for group 2.  I have double checked all
the mroutes & the RP mapping ACL's etc.

appreciate any insights or pointers..

Neil


More information about the cisco-nsp mailing list