[c-nsp] telemetry on IOS XE

[Randy Rooney]

For XR - make sure you specify src addr in TPA context -
 tpa
 vrf abc
  address-family ipv4
   update-source MgmtEth0/RP0/CPU0/0

Have not played with XE telemetry but I would check subsystem components:
  show platform software yang-management process

HTH

On Sat, Jun 20, 2020 at 3:43 AM Dave Bell <dave at geordish.org> wrote:

> A while back when I was experimenting this is the configuration I had
> running on a CSR1k 16.12.0
>
> netconf-yang
>
> telemetry ietf subscription 1
>  encoding encode-kvgpb
>  filter xpath
> /process-cpu-ios-xe-oper:cpu-usage/cpu-utilization/five-seconds
>  source-address 192.168.0.2
>  stream yang-push
>  update-policy periodic 5000
>  receiver ip address 10.0.2.1 57000 protocol grpc-tcp
>
>
> Apart from the VRF statement that is exactly what you have.
>
> Coincidently I’m trying to get this working on IOS XR with no success. A
> variety of versions, and I’m also having issues. I’m using the same config
> I tested a while back, but as with you I’m trying to source it in a VRF.
>
> I’ve got a TAC case open, however I’ve got a feeling it’s going to come
> back as unsupported.
>
> On Sat, 20 Jun 2020 at 06:42, Robert Hass <robhass at gmail.com> wrote:
>
> > Yes I did
> >
> > #sh run | inc netconf
> > netconf-yang
> >
> > #show platform software yang-management process
> > confd            : Running
> > nesd             : Running
> > syncfd           : Running
> > ncsshd           : Running
> > dmiauthd         : Running
> > nginx            : Running
> > ndbmand          : Running
> > pubd             : Running
> > gnmib            : Not Running
> >
> > On Sat, Jun 20, 2020 at 12:02 AM Dave Bell <dave at geordish.org> wrote:
> >
> >> Have you enabled netconf-yang?
> >>
> >> On Fri, 19 Jun 2020 at 20:46, Robert Hass <robhass at gmail.com> wrote:
> >>
> >>> Hi
> >>> I'm trying to run telemetry on IOS XE (Catalyst 9300) but without lack.
> >>>
> >>> My config:
> >>>
> >>> test#sh run | sec tele
> >>> telemetry ietf subscription 1
> >>>  encoding encode-kvgpb
> >>>  filter xpath
> >>> /process-cpu-ios-xe-oper:cpu-usage/cpu-utilization/five-seconds
> >>>  source-address 10.0.0.147
> >>>  source-vrf Mgmt-vrf
> >>>  stream yang-push
> >>>  update-policy periodic 500
> >>>  receiver ip address 10.0.3.16 12345 protocol grpc-tcp
> >>>
> >>> But it's not working:
> >>> #show telemetry ietf subscription all
> >>> The process for the command is not responding or is otherwise
> unavailable
> >>>
> >>> Any ideas ?
> >>>
> >>> Running IOS XE  17.02.01
> >>>
> >>> Rob
> >>> _______________________________________________
> >>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> >>> https://puck.nether.net/mailman/listinfo/cisco-nsp
> >>> archive at http://puck.nether.net/pipermail/cisco-nsp/
> >>>
> >>
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>