[cisco-voip] Problems with CallerID on a PRI connected to PA-VXC-2TE1

[Dave Temkin]

Try:

 isdn outgoing display-ie
on your serial interface for the PRI



-Dave

On Mon, 7 Feb 2005, John Lange wrote:

> We have an Asterisk Phone system that places outbound calls using SIP
> via a Cisco PA-VXC-2TE1+ card connected to an Allstream PRI.
>
> Try as we might we can not get callerid number working on outbound
> calls.
>
> Strangely, CallerID name display works perfectly fine.
>
> Allstream insists that their equipment is configured correctly and that
> they will accept the name/number we set on calls.
>
> So the question is, what is the setting on the Cisco so that it passes
> CID name and number?
>
> The following is the trace provided by Allstream on a sample outbound
> call from our equipment. As you can see DSP is set properly to the name
> but there is no CGN portion. (From my conversations with them my
> understanding is the CGN is the number, DSP is the name?)
>
> Below this trace is the current configuration for the Cisco.
>
> Any suggestions are welcome.
>
> Thanks.
>
> --------------
>
> <== 03:12:51:05.11   (CM Time: 02:15:56:55.12).
> <== Q931: SETUP:     from S[7040] L[1,186,0] E[26,185,0] SPA[----]
>   CR:  0,01 6C
>   BC:  speech
>        64 kbit/s
>        circuit mode
>        mu-law speech
>   CID: 18
>        LENGTH: 03
>        Channel Selection Info: As Indicated in Following Octets
>        D-Channel Indicator: D-Channel NOT indicated
>        Preferred/Exclusive: Exclusive
>        Interface type = primary rate
>        Interface Identifier: IID Implicitly Identified
>        Channel Type: B - Channel Units (3).
>        Number Map: Channel is indicated by the number following.
>        Coding Standard: CCITT
>        Channel Number = 23
>   DSP: ±OpenIT
>   CDN: unknown
>        unknown
>        14162045956
> --------------
>
>
> Current configuration : 3012 bytes
> !
> ! Last configuration change at 14:10:36 CST Thu Feb 3 2005
> ! NVRAM config last updated at 13:54:27 CST Tue Feb 1 2005
> !
> version 12.2
> service timestamps debug datetime msec
> service timestamps log datetime msec
> service password-encryption
> !
> hostname WPG-SIPgw-01
> !
> boot system slot0:c7200-is-mz.122-15.T14.bin
> card type t1 1
> logging queue-limit 100
> enable secret 5 ***REMOVED***
> !
> clock timezone CST -6
> clock summer-time CDT recurring 1 Sun Apr 2:00 4 Sun Oct 2:00
> dspint DSPfarm1/0
> !
> ip subnet-zero
> !
> !
> ip cef
> !
> isdn switch-type primary-dms100
> !
> !
> !
> voice service voip
>  sip
> !
> !
> !
> !
> !
> !
> !
> no voice hpi capture buffer
> no voice hpi capture destination
> !
> !
> mta receive maximum-recipients 0
> !
> !
> controller T1 1/0
>  framing esf
>  linecode b8zs
>  cablelength long 0db
>  pri-group timeslots 1-24
> !
> controller T1 1/1
>  shutdown
>  framing esf
>  linecode b8zs
>  cablelength long 0db
> !
> !
> !
> interface FastEthernet0/0
>  ip address XXX.XXX.106.150 255.255.255.0
>  duplex full
> !
> interface Serial1/0:23
>  no ip address
>  no logging event link-status
>  isdn switch-type primary-dms100
>  isdn incoming-voice voice
>  no cdp enable
> !
> ip classless
> ip route 0.0.0.0 0.0.0.0 XXX.XXX.106.1
> no ip http server
> !
> !
> !
> access-list 10 permit XXX.XXX.106.4
> access-list 10 permit XXX.XXX.106.5
> !
> !
> call rsvp-sync
> !
> voice-port 1/0:23
> !
> !
> mgcp profile default
> !
> dial-peer cor custom
> !
> !
> !
> dial-peer voice 100 voip
>  application session
>  destination-pattern XXXXX54235
>  progress_ind setup enable 3
>  session protocol sipv2
>  session target ipv4:XXX.XXX.99.50
>  session transport udp
> !
> dial-peer voice 101 voip
>  application session
>  destination-pattern XXXXX54236
>  progress_ind setup enable 3
>  session protocol sipv2
>  session target ipv4:XXX.XXX.102.59
>  session transport udp
> !
> dial-peer voice 5000 pots
>  application session
>  destination-pattern .......
>  direct-inward-dial
>  port 1/0:23
> !
> dial-peer voice 102 voip
>  application session
>  destination-pattern XXXXX74002
>  progress_ind setup enable 3
>  session protocol sipv2
>  session target ipv4:XXX.XXX.102.59
>  session transport udp
> !
> dial-peer voice 103 voip
>  application session
>  destination-pattern XXXXX74003
>  progress_ind setup enable 3
>  session protocol sipv2
>  session target ipv4:XXX.XXX.102.59
>  session transport udp
>  codec g711ulaw
> !
> dial-peer voice 104 voip
>  application session
>  destination-pattern XXXXX74004
>  progress_ind setup enable 3
>  session protocol sipv2
>  session target ipv4:XXX.XXX.102.59
>  session transport udp
> !
> dial-peer voice 105 voip
>  destination-pattern XXXXX74005
>  progress_ind setup enable 3
>  session protocol sipv2
>  session target ipv4:XXX.XXX.102.59
>  session transport udp
> !
> dial-peer voice 5001 pots
>  incoming called-number 1..........
>  direct-inward-dial
>  port 1/0:23
>  prefix 1
> !
> sip-ua
>  calling-info sip-to-pstn number set XXXXX74006
> !
> !
> gatekeeper
>  shutdown
> !
> !
> line con 0
>  stopbits 1
> line aux 0
>  stopbits 1
> line vty 0 4
>  access-class 10 in
>  exec-timeout 60 0
>  password ***REMOVED***
>  login
> !
> ntp clock-period 17180028
> ntp server XXX.XXX.111.252
> !
> end
>
>