[cisco-voip] Problems with CallerID on a PRI connected to PA-VXC-2TE1

[John Lange]

Thanks Dave.

Unfortunately we tried that setting but it had no effect.

Its very confusing to me how the Name information could be passing
properly but not the number info.

If you have any other suggestions I'd be glad to hear them.

Thanks.

John


On Mon, 2005-02-07 at 12:22, Dave Temkin wrote:
> Try:
> 
>  isdn outgoing display-ie
> on your serial interface for the PRI
> 
> 
> 
> -Dave
> 
> On Mon, 7 Feb 2005, John Lange wrote:
> 
> > We have an Asterisk Phone system that places outbound calls using SIP
> > via a Cisco PA-VXC-2TE1+ card connected to an Allstream PRI.
> >
> > Try as we might we can not get callerid number working on outbound
> > calls.
> >
> > Strangely, CallerID name display works perfectly fine.
> >
> > Allstream insists that their equipment is configured correctly and that
> > they will accept the name/number we set on calls.
> >
> > So the question is, what is the setting on the Cisco so that it passes
> > CID name and number?
> >
> > The following is the trace provided by Allstream on a sample outbound
> > call from our equipment. As you can see DSP is set properly to the name
> > but there is no CGN portion. (From my conversations with them my
> > understanding is the CGN is the number, DSP is the name?)
> >
> > Below this trace is the current configuration for the Cisco.
> >
> > Any suggestions are welcome.
> >
> > Thanks.
> >
> > --------------
> >
> > <== 03:12:51:05.11   (CM Time: 02:15:56:55.12).
> > <== Q931: SETUP:     from S[7040] L[1,186,0] E[26,185,0] SPA[----]
> >   CR:  0,01 6C
> >   BC:  speech
> >        64 kbit/s
> >        circuit mode
> >        mu-law speech
> >   CID: 18
> >        LENGTH: 03
> >        Channel Selection Info: As Indicated in Following Octets
> >        D-Channel Indicator: D-Channel NOT indicated
> >        Preferred/Exclusive: Exclusive
> >        Interface type = primary rate
> >        Interface Identifier: IID Implicitly Identified
> >        Channel Type: B - Channel Units (3).
> >        Number Map: Channel is indicated by the number following.
> >        Coding Standard: CCITT
> >        Channel Number = 23
> >   DSP: ±OpenIT
> >   CDN: unknown
> >        unknown
> >        14162045956
> > --------------
> >
> >
> > Current configuration : 3012 bytes
> > !
> > ! Last configuration change at 14:10:36 CST Thu Feb 3 2005
> > ! NVRAM config last updated at 13:54:27 CST Tue Feb 1 2005
> > !
> > version 12.2
> > service timestamps debug datetime msec
> > service timestamps log datetime msec
> > service password-encryption
> > !
> > hostname WPG-SIPgw-01
> > !
> > boot system slot0:c7200-is-mz.122-15.T14.bin
> > card type t1 1
> > logging queue-limit 100
> > enable secret 5 ***REMOVED***
> > !
> > clock timezone CST -6
> > clock summer-time CDT recurring 1 Sun Apr 2:00 4 Sun Oct 2:00
> > dspint DSPfarm1/0
> > !
> > ip subnet-zero
> > !
> > !
> > ip cef
> > !
> > isdn switch-type primary-dms100
> > !
> > !
> > !
> > voice service voip
> >  sip
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > no voice hpi capture buffer
> > no voice hpi capture destination
> > !
> > !
> > mta receive maximum-recipients 0
> > !
> > !
> > controller T1 1/0
> >  framing esf
> >  linecode b8zs
> >  cablelength long 0db
> >  pri-group timeslots 1-24
> > !
> > controller T1 1/1
> >  shutdown
> >  framing esf
> >  linecode b8zs
> >  cablelength long 0db
> > !
> > !
> > !
> > interface FastEthernet0/0
> >  ip address XXX.XXX.106.150 255.255.255.0
> >  duplex full
> > !
> > interface Serial1/0:23
> >  no ip address
> >  no logging event link-status
> >  isdn switch-type primary-dms100
> >  isdn incoming-voice voice
> >  no cdp enable
> > !
> > ip classless
> > ip route 0.0.0.0 0.0.0.0 XXX.XXX.106.1
> > no ip http server
> > !
> > !
> > !
> > access-list 10 permit XXX.XXX.106.4
> > access-list 10 permit XXX.XXX.106.5
> > !
> > !
> > call rsvp-sync
> > !
> > voice-port 1/0:23
> > !
> > !
> > mgcp profile default
> > !
> > dial-peer cor custom
> > !
> > !
> > !
> > dial-peer voice 100 voip
> >  application session
> >  destination-pattern XXXXX54235
> >  progress_ind setup enable 3
> >  session protocol sipv2
> >  session target ipv4:XXX.XXX.99.50
> >  session transport udp
> > !
> > dial-peer voice 101 voip
> >  application session
> >  destination-pattern XXXXX54236
> >  progress_ind setup enable 3
> >  session protocol sipv2
> >  session target ipv4:XXX.XXX.102.59
> >  session transport udp
> > !
> > dial-peer voice 5000 pots
> >  application session
> >  destination-pattern .......
> >  direct-inward-dial
> >  port 1/0:23
> > !
> > dial-peer voice 102 voip
> >  application session
> >  destination-pattern XXXXX74002
> >  progress_ind setup enable 3
> >  session protocol sipv2
> >  session target ipv4:XXX.XXX.102.59
> >  session transport udp
> > !
> > dial-peer voice 103 voip
> >  application session
> >  destination-pattern XXXXX74003
> >  progress_ind setup enable 3
> >  session protocol sipv2
> >  session target ipv4:XXX.XXX.102.59
> >  session transport udp
> >  codec g711ulaw
> > !
> > dial-peer voice 104 voip
> >  application session
> >  destination-pattern XXXXX74004
> >  progress_ind setup enable 3
> >  session protocol sipv2
> >  session target ipv4:XXX.XXX.102.59
> >  session transport udp
> > !
> > dial-peer voice 105 voip
> >  destination-pattern XXXXX74005
> >  progress_ind setup enable 3
> >  session protocol sipv2
> >  session target ipv4:XXX.XXX.102.59
> >  session transport udp
> > !
> > dial-peer voice 5001 pots
> >  incoming called-number 1..........
> >  direct-inward-dial
> >  port 1/0:23
> >  prefix 1
> > !
> > sip-ua
> >  calling-info sip-to-pstn number set XXXXX74006
> > !
> > !
> > gatekeeper
> >  shutdown
> > !
> > !
> > line con 0
> >  stopbits 1
> > line aux 0
> >  stopbits 1
> > line vty 0 4
> >  access-class 10 in
> >  exec-timeout 60 0
> >  password ***REMOVED***
> >  login
> > !
> > ntp clock-period 17180028
> > ntp server XXX.XXX.111.252
> > !
> > end
> >
> >