[cisco-voip] Caller ID on MGCP FXS Port

[Wes Sisk]

Hi Court,

Yes, it is possible to implement a hunt group in h323 configuration by 
using multiple pots peers with the same destination pattern and varying 
'preference'

dial-peer voice 1 pots
destination-pattern 20..
port 0/0
preference 0
prefix ,,,,
dial-peer voice 2 pots
destination-pattern 20..
port 0/1
preference 1
prefix ,,,,
(etc.)

Remember that on POTS dial-peers any digits not explicitly matched are 
pulsed out of the port as DTMF.  So in the above example, if the CM 
sends an h323 call setup to the MRP with calledpartynumber=2045 the call 
will route to port 0/0.  The MRP will supply ring voltage down the line 
and then 4 seconds later (4 commas) it will pulse out the digits 4 5.  
All the normal h323 dial-peer configurations are still needed.  
Supplimentary info:
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a0080147524.shtml

/Wes

/Wes

Court Schuett wrote:

>If that is the case, is there any way to do hunt groups off of H323?  I
>put in a TAC case the other day and they recommended I go MGCP.  When I
>tried to do it with H323 (that's the way it was initially) when I tried
>to do a hunt group, it just went to busy because it couldn't find any of
>the numbers in the hunt group.
>
>Thanks
>
>-Court
>
>-----Original Message-----
>From: Wes Sisk [mailto:wsisk at cisco.com] 
>Sent: Tuesday, February 08, 2005 1:43 PM
>To: Court Schuett
>Cc: cisco-voip at puck.nether.net
>Subject: Re: [cisco-voip] Caller ID on MGCP FXS Port
>
>analog mgcp does not yet support callerid, you will need to use h323.
>
>/Wes
>
>Court Schuett wrote:
>
>  
>
>>Hello,
>>
>>I've got a Gold Fax fax server set up to run off of 4 FXS ports on an
>>ICS. I have two small hunt groups set up to handle the inbound calls
>>    
>>
>but
>  
>
>>I'm having trouble passing the caller id information into the fax
>>    
>>
>lines.
>  
>
>>What I would like to do is this:
>>HP: 7060 -> hunt group that routes to FaxModem1 on server and passes a
>>predetermined number (it can really be anything) to the fax server.
>>HP: 7050 -> hunt group that routes to FaxModem2-4 on server and passes
>>    
>>
>a
>  
>
>>different predetermined number.
>>
>>I have almost everything set up. I have both hunt groups set up and
>>working correctly. 7060 is ringing to the correct modem, and 7050 is
>>ringing to all three modems (longest idle) correctly. The only problem
>>is that I can't seem to pass any sort of caller id to the FXS ports.
>>I've hooked up a regular analog phone and it's not getting anything
>>either. The CCM is connected to the FXS ports with MGCP.
>>
>>CCM: 4.0(1)sr2a
>>HW: ICS7750-MRP300 (MPC860P)
>>SW: 12.3(2)XA
>>
>>Any ideas?
>>
>>Thanks.
>>
>>_______________________________________________
>>cisco-voip mailing list
>>cisco-voip at puck.nether.net
>>https://puck.nether.net/mailman/listinfo/cisco-voip
>> 
>>
>>    
>>