[cisco-voip] Problems with CallerID on a PRI connected to
PA-VXC-2TE1
John Lange
john.lange at open-it.ca
Tue Feb 8 17:17:57 EST 2005
Thanks Peter.
To answer your questions;
show dial-peer voice shows "none" for CLID restriction.
Incoming callerid name and number is working perfectly. We see it on the
router just fine for calls coming in from the PRI as well as incoming
SIP calls.
We were aware of the document at the link you sent and it has given us
some ideas to try but still we haven't got it working.
Thanks for your suggestions and please feel free to make some more.
John
On Tue, 2005-02-08 at 12:51, peter.casanave at us.army.mil wrote:
> when you do the show dial-peer voice ### command do you see CLID restriction under codec display? Also, on the router do you see the CLID coming in?
>
> V/R,
> PETER CASANAVE
> SFC, USA
> BBN Platoon Sergeant
>
> ----- Original Message -----
> From: John Lange <john.lange at open-it.ca>
> Date: Tuesday, February 8, 2005 12:27 pm
> Subject: Re: [cisco-voip] Problems with CallerID on a PRI connected to PA-VXC-2TE1
>
> > Thanks Dave.
> >
> > Unfortunately we tried that setting but it had no effect.
> >
> > Its very confusing to me how the Name information could be passing
> > properly but not the number info.
> >
> > If you have any other suggestions I'd be glad to hear them.
> >
> > Thanks.
> >
> > John
> >
> >
> > On Mon, 2005-02-07 at 12:22, Dave Temkin wrote:
> > > Try:
> > >
> > > isdn outgoing display-ie
> > > on your serial interface for the PRI
> > >
> > >
> > >
> > > -Dave
> > >
> > > On Mon, 7 Feb 2005, John Lange wrote:
> > >
> > > > We have an Asterisk Phone system that places outbound calls
> > using SIP
> > > > via a Cisco PA-VXC-2TE1+ card connected to an Allstream PRI.
> > > >
> > > > Try as we might we can not get callerid number working on outbound
> > > > calls.
> > > >
> > > > Strangely, CallerID name display works perfectly fine.
> > > >
> > > > Allstream insists that their equipment is configured correctly
> > and that
> > > > they will accept the name/number we set on calls.
> > > >
> > > > So the question is, what is the setting on the Cisco so that
> > it passes
> > > > CID name and number?
> > > >
> > > > The following is the trace provided by Allstream on a sample
> > outbound> > call from our equipment. As you can see DSP is set
> > properly to the name
> > > > but there is no CGN portion. (From my conversations with them my
> > > > understanding is the CGN is the number, DSP is the name?)
> > > >
> > > > Below this trace is the current configuration for the Cisco.
> > > >
> > > > Any suggestions are welcome.
> > > >
> > > > Thanks.
> > > >
> > > > --------------
> > > >
> > > > <== 03:12:51:05.11 (CM Time: 02:15:56:55.12).
> > > > <== Q931: SETUP: from S[7040] L[1,186,0] E[26,185,0] SPA[--
> > --]
> > > > CR: 0,01 6C
> > > > BC: speech
> > > > 64 kbit/s
> > > > circuit mode
> > > > mu-law speech
> > > > CID: 18
> > > > LENGTH: 03
> > > > Channel Selection Info: As Indicated in Following Octets
> > > > D-Channel Indicator: D-Channel NOT indicated
> > > > Preferred/Exclusive: Exclusive
> > > > Interface type = primary rate
> > > > Interface Identifier: IID Implicitly Identified
> > > > Channel Type: B - Channel Units (3).
> > > > Number Map: Channel is indicated by the number following.
> > > > Coding Standard: CCITT
> > > > Channel Number = 23
> > > > DSP: ±OpenIT
> > > > CDN: unknown
> > > > unknown
> > > > 14162045956
> > > > --------------
> > > >
> > > >
> > > > Current configuration : 3012 bytes
> > > > !
> > > > ! Last configuration change at 14:10:36 CST Thu Feb 3 2005
> > > > ! NVRAM config last updated at 13:54:27 CST Tue Feb 1 2005
> > > > !
> > > > version 12.2
> > > > service timestamps debug datetime msec
> > > > service timestamps log datetime msec
> > > > service password-encryption
> > > > !
> > > > hostname WPG-SIPgw-01
> > > > !
> > > > boot system slot0:c7200-is-mz.122-15.T14.bin
> > > > card type t1 1
> > > > logging queue-limit 100
> > > > enable secret 5 ***REMOVED***
> > > > !
> > > > clock timezone CST -6
> > > > clock summer-time CDT recurring 1 Sun Apr 2:00 4 Sun Oct 2:00
> > > > dspint DSPfarm1/0
> > > > !
> > > > ip subnet-zero
> > > > !
> > > > !
> > > > ip cef
> > > > !
> > > > isdn switch-type primary-dms100
> > > > !
> > > > !
> > > > !
> > > > voice service voip
> > > > sip
> > > > !
> > > > !
> > > > !
> > > > !
> > > > !
> > > > !
> > > > !
> > > > no voice hpi capture buffer
> > > > no voice hpi capture destination
> > > > !
> > > > !
> > > > mta receive maximum-recipients 0
> > > > !
> > > > !
> > > > controller T1 1/0
> > > > framing esf
> > > > linecode b8zs
> > > > cablelength long 0db
> > > > pri-group timeslots 1-24
> > > > !
> > > > controller T1 1/1
> > > > shutdown
> > > > framing esf
> > > > linecode b8zs
> > > > cablelength long 0db
> > > > !
> > > > !
> > > > !
> > > > interface FastEthernet0/0
> > > > ip address XXX.XXX.106.150 255.255.255.0
> > > > duplex full
> > > > !
> > > > interface Serial1/0:23
> > > > no ip address
> > > > no logging event link-status
> > > > isdn switch-type primary-dms100
> > > > isdn incoming-voice voice
> > > > no cdp enable
> > > > !
> > > > ip classless
> > > > ip route 0.0.0.0 0.0.0.0 XXX.XXX.106.1
> > > > no ip http server
> > > > !
> > > > !
> > > > !
> > > > access-list 10 permit XXX.XXX.106.4
> > > > access-list 10 permit XXX.XXX.106.5
> > > > !
> > > > !
> > > > call rsvp-sync
> > > > !
> > > > voice-port 1/0:23
> > > > !
> > > > !
> > > > mgcp profile default
> > > > !
> > > > dial-peer cor custom
> > > > !
> > > > !
> > > > !
> > > > dial-peer voice 100 voip
> > > > application session
> > > > destination-pattern XXXXX54235
> > > > progress_ind setup enable 3
> > > > session protocol sipv2
> > > > session target ipv4:XXX.XXX.99.50
> > > > session transport udp
> > > > !
> > > > dial-peer voice 101 voip
> > > > application session
> > > > destination-pattern XXXXX54236
> > > > progress_ind setup enable 3
> > > > session protocol sipv2
> > > > session target ipv4:XXX.XXX.102.59
> > > > session transport udp
> > > > !
> > > > dial-peer voice 5000 pots
> > > > application session
> > > > destination-pattern .......
> > > > direct-inward-dial
> > > > port 1/0:23
> > > > !
> > > > dial-peer voice 102 voip
> > > > application session
> > > > destination-pattern XXXXX74002
> > > > progress_ind setup enable 3
> > > > session protocol sipv2
> > > > session target ipv4:XXX.XXX.102.59
> > > > session transport udp
> > > > !
> > > > dial-peer voice 103 voip
> > > > application session
> > > > destination-pattern XXXXX74003
> > > > progress_ind setup enable 3
> > > > session protocol sipv2
> > > > session target ipv4:XXX.XXX.102.59
> > > > session transport udp
> > > > codec g711ulaw
> > > > !
> > > > dial-peer voice 104 voip
> > > > application session
> > > > destination-pattern XXXXX74004
> > > > progress_ind setup enable 3
> > > > session protocol sipv2
> > > > session target ipv4:XXX.XXX.102.59
> > > > session transport udp
> > > > !
> > > > dial-peer voice 105 voip
> > > > destination-pattern XXXXX74005
> > > > progress_ind setup enable 3
> > > > session protocol sipv2
> > > > session target ipv4:XXX.XXX.102.59
> > > > session transport udp
> > > > !
> > > > dial-peer voice 5001 pots
> > > > incoming called-number 1..........
> > > > direct-inward-dial
> > > > port 1/0:23
> > > > prefix 1
> > > > !
> > > > sip-ua
> > > > calling-info sip-to-pstn number set XXXXX74006
> > > > !
> > > > !
> > > > gatekeeper
> > > > shutdown
> > > > !
> > > > !
> > > > line con 0
> > > > stopbits 1
> > > > line aux 0
> > > > stopbits 1
> > > > line vty 0 4
> > > > access-class 10 in
> > > > exec-timeout 60 0
> > > > password ***REMOVED***
> > > > login
> > > > !
> > > > ntp clock-period 17180028
> > > > ntp server XXX.XXX.111.252
> > > > !
> > > > end
> > > >
> > > >
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
--
More information about the cisco-voip
mailing list