[cisco-voip] Caller ID on MGCP FXS Port

[peter.casanave at us.army.mil]

you should be able to also assign the voice-ports to a trunk group then point one dialpeer to the respective trunk group wrather than creating several dial-peers. I used that with FXOs and it worked great.

V/R,
PETER CASANAVE
SFC, USA
BBN Platoon Sergeant

----- Original Message -----
From: Wes Sisk <wsisk at cisco.com>
Date: Tuesday, February 8, 2005 2:24 pm
Subject: Re: [cisco-voip] Caller ID on MGCP FXS Port

> Hi Court,
> 
> Yes, it is possible to implement a hunt group in h323 
> configuration by 
> using multiple pots peers with the same destination pattern and 
> varying 
> 'preference'
> 
> dial-peer voice 1 pots
> destination-pattern 20..
> port 0/0
> preference 0
> prefix ,,,,
> dial-peer voice 2 pots
> destination-pattern 20..
> port 0/1
> preference 1
> prefix ,,,,
> (etc.)
> 
> Remember that on POTS dial-peers any digits not explicitly matched 
> are 
> pulsed out of the port as DTMF.  So in the above example, if the 
> CM 
> sends an h323 call setup to the MRP with calledpartynumber=2045 
> the call 
> will route to port 0/0.  The MRP will supply ring voltage down the 
> line 
> and then 4 seconds later (4 commas) it will pulse out the digits 4 
> 5.  
> All the normal h323 dial-peer configurations are still needed.  
> Supplimentary info:
> http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
> http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a0080147524.shtml
> 
> /Wes
> 
> /Wes
> 
> Court Schuett wrote:
> 
> >If that is the case, is there any way to do hunt groups off of 
> H323?  I
> >put in a TAC case the other day and they recommended I go MGCP.  
> When I
> >tried to do it with H323 (that's the way it was initially) when I 
> tried>to do a hunt group, it just went to busy because it couldn't 
> find any of
> >the numbers in the hunt group.
> >
> >Thanks
> >
> >-Court
> >
> >-----Original Message-----
> >From: Wes Sisk [wsisk at cisco.com] 
> >Sent: Tuesday, February 08, 2005 1:43 PM
> >To: Court Schuett
> >Cc: cisco-voip at puck.nether.net
> >Subject: Re: [cisco-voip] Caller ID on MGCP FXS Port
> >
> >analog mgcp does not yet support callerid, you will need to use h323.
> >
> >/Wes
> >
> >Court Schuett wrote:
> >
> >  
> >
> >>Hello,
> >>
> >>I've got a Gold Fax fax server set up to run off of 4 FXS ports 
> on an
> >>ICS. I have two small hunt groups set up to handle the inbound calls
> >>    
> >>
> >but
> >  
> >
> >>I'm having trouble passing the caller id information into the fax
> >>    
> >>
> >lines.
> >  
> >
> >>What I would like to do is this:
> >>HP: 7060 -> hunt group that routes to FaxModem1 on server and 
> passes a
> >>predetermined number (it can really be anything) to the fax server.
> >>HP: 7050 -> hunt group that routes to FaxModem2-4 on server and 
> passes>>    
> >>
> >a
> >  
> >
> >>different predetermined number.
> >>
> >>I have almost everything set up. I have both hunt groups set up and
> >>working correctly. 7060 is ringing to the correct modem, and 
> 7050 is
> >>ringing to all three modems (longest idle) correctly. The only 
> problem>>is that I can't seem to pass any sort of caller id to the 
> FXS ports.
> >>I've hooked up a regular analog phone and it's not getting anything
> >>either. The CCM is connected to the FXS ports with MGCP.
> >>
> >>CCM: 4.0(1)sr2a
> >>HW: ICS7750-MRP300 (MPC860P)
> >>SW: 12.3(2)XA
> >>
> >>Any ideas?
> >>
> >>Thanks.
> >>
> >>_______________________________________________
> >>cisco-voip mailing list
> >>cisco-voip at puck.nether.net
> >>https://puck.nether.net/mailman/listinfo/cisco-voip
> >> 
> >>
> >>    
> >>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>