[cisco-voip] CCM - Leading zeroes on calling number

[Vincent De Keyzer]

Where is that exactly? Couldn't find it in "Service Parameters"...

I'm running 4.0(1)sr2 BTW

Vincent

> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-
> bounces at puck.nether.net] On Behalf Of Marcus Lundbom
> Sent: mardi 25 janvier 2005 0:22
> To: cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] CCM - Leading zeroes on calling number
> 
> or simply use the advanced service parameters of ccm to apply the
> correct number of digits on the inbound calls .....
> 
> Best regards,
> 
> 
> /M
> 
> 
> 
> ________________________________
> 
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of chris donnelly
> Sent: Monday, January 24, 2005 5:35 PM
> To: Vincent De Keyzer; cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] CCM - Leading zeroes on calling number
> 
> 
> 
> We do it this way....
> 
> 
> 
> translation-rule 1
> 
>  Rule 1 ^0.% 90
> 
>  Rule 2 ^1.% 901
> 
>  Rule 3 ^2.% 902
> 
>  Rule 4 ^3.% 903
> 
>  Rule 5 ^4.% 904
> 
>  Rule 6 ^5.% 905
> 
>  Rule 7 ^6.% 906
> 
>  Rule 8 ^7.% 907
> 
>  Rule 9 ^8.% 908
> 
>  Rule 10 ^9.% 909
> 
> 
> 
> Then apply the translation rule to a dial-peer
> 
> 
> 
> 
> 
> dial-peer voice 102 voip
> 
>  preference 2
> 
>  destination-pattern  xxx
> 
>  progress_ind setup enable 3
> 
>  progress_ind alert enable 8
> 
>  progress_ind progress enable 8
> 
>  progress_ind connect enable 8
> 
>  translate-outgoing calling 1
> 
>  modem passthrough nse codec g711ulaw
> 
>  voice-class codec 1
> 
>  voice-class h323 1
> 
>  session target ipv4:xxx.xxx.xxx.xxx
> 
>  dtmf-relay h245-alphanumeric
> 
>  fax-relay ecm disable
> 
>  fax rate disable
> 
>  fax nsf 000000
> 
>  fax protocol none
> 
>  no vad
> 
> 
> 
> ________________________________
> 
> From: Vincent De Keyzer [mailto:vincent at dekeyzer.net]
> Sent: 24 January 2005 14:02
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] CCM - Leading zeroes on calling number
> 
> 
> 
> Hello,
> 
> 
> 
> I am facing (maybe because I'm in Europe) a cosmetic issue with
> CallManager and a Cisco2821 as gateway.
> 
> 
> 
> When I receive an incoming call on the gateway, the set-up message
> appears as follows:
> 
> 
> 
> Jan 24 14:45:16.918 CET: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8
> callref = 0x7194
> 
>         Sending Complete
> 
>         Bearer Capability i = 0x8090A3
> 
>                 Standard = CCITT
> 
>                 Transer Capability = Speech
> 
>                 Transfer Mode = Circuit
> 
>                 Transfer Rate = 64 kbit/s
> 
>         Channel ID i = 0xA9838A
> 
>                 Exclusive, Channel 10
> 
>         Calling Party Number i = 0x2181, '23334455'
> 
>                 Plan:ISDN, Type:National
> 
>         Called Party Number i = 0xA1, '24447722'
> 
>                 Plan:ISDN, Type:National
> 
>         Sending Complete
> 
> 
> 
> When the call hits my IP phone, it shows calling number '23334455'
> instead of what I had wished, which is '023334455' (since it's a
> national call).
> 
> 
> 
> In the same way, for an international call from, say, France, I would
> receive on the PRI '33612345678' and 'Type: International', which I
> would like to appear on the display of the IP phone as '0033612345678'.
> 
> 
> 
> How can I add one or two zeros to the calling number based depending on
> its type ('National' or 'International')?
> 
> 
> 
> Vincent
> 
> 
> _____________________________________________________________________
> This message has been checked for all known viruses by the MessageLabs
> Virus Control Centre.
> 
> 
> 
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip