[cisco-voip] CCM - Leading zeroes on calling number

[Vincent De Keyzer]

Erick,

those fields are already filled in they way I would have done it. 

But they are within section "Clusterwide Parameters (Device - PRI and MGCP
Gateway)", so I imagine they are taken into account when using MGCP only
(which is not my case)?

Vincent


> -----Original Message-----
> From: Erick B. [mailto:erickbe at yahoo.com]
> Sent: vendredi 28 janvier 2005 4:27
> To: Vincent De Keyzer; 'Marcus Lundbom'; cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] CCM - Leading zeroes on calling number
> 
> Vincent,
> 
> Open up Service Parameters menu, then choose Call
> Manager service. Click the Advanced button to reveal
> advanced settings.
> 
> Go down to PRI settings section and there should be 4
> fields that are blank in a row if not set already. One
> for local prefix, one for national prefix, and one for
> international prefix. One for unknown. There may be
> another one.
> 
> --- Vincent De Keyzer <vincent at dekeyzer.net> wrote:
> 
> > Where is that exactly? Couldn't find it in "Service
> > Parameters"...
> >
> > I'm running 4.0(1)sr2 BTW
> >
> > Vincent
> >
> > > -----Original Message-----
> > > From: cisco-voip-bounces at puck.nether.net
> > [mailto:cisco-voip-
> > > bounces at puck.nether.net] On Behalf Of Marcus
> > Lundbom
> > > Sent: mardi 25 janvier 2005 0:22
> > > To: cisco-voip at puck.nether.net
> > > Subject: RE: [cisco-voip] CCM - Leading zeroes on
> > calling number
> > >
> > > or simply use the advanced service parameters of
> > ccm to apply the
> > > correct number of digits on the inbound calls
> > .....
> > >
> > > Best regards,
> > >
> > >
> > > /M
> > >
> > >
> > >
> > > ________________________________
> > >
> > > From: cisco-voip-bounces at puck.nether.net
> > > [mailto:cisco-voip-bounces at puck.nether.net] On
> > Behalf Of chris donnelly
> > > Sent: Monday, January 24, 2005 5:35 PM
> > > To: Vincent De Keyzer; cisco-voip at puck.nether.net
> > > Subject: RE: [cisco-voip] CCM - Leading zeroes on
> > calling number
> > >
> > >
> > >
> > > We do it this way....
> > >
> > >
> > >
> > > translation-rule 1
> > >
> > >  Rule 1 ^0.% 90
> > >
> > >  Rule 2 ^1.% 901
> > >
> > >  Rule 3 ^2.% 902
> > >
> > >  Rule 4 ^3.% 903
> > >
> > >  Rule 5 ^4.% 904
> > >
> > >  Rule 6 ^5.% 905
> > >
> > >  Rule 7 ^6.% 906
> > >
> > >  Rule 8 ^7.% 907
> > >
> > >  Rule 9 ^8.% 908
> > >
> > >  Rule 10 ^9.% 909
> > >
> > >
> > >
> > > Then apply the translation rule to a dial-peer
> > >
> > >
> > >
> > >
> > >
> > > dial-peer voice 102 voip
> > >
> > >  preference 2
> > >
> > >  destination-pattern  xxx
> > >
> > >  progress_ind setup enable 3
> > >
> > >  progress_ind alert enable 8
> > >
> > >  progress_ind progress enable 8
> > >
> > >  progress_ind connect enable 8
> > >
> > >  translate-outgoing calling 1
> > >
> > >  modem passthrough nse codec g711ulaw
> > >
> > >  voice-class codec 1
> > >
> > >  voice-class h323 1
> > >
> > >  session target ipv4:xxx.xxx.xxx.xxx
> > >
> > >  dtmf-relay h245-alphanumeric
> > >
> > >  fax-relay ecm disable
> > >
> > >  fax rate disable
> > >
> > >  fax nsf 000000
> > >
> > >  fax protocol none
> > >
> > >  no vad
> > >
> > >
> > >
> > > ________________________________
> > >
> > > From: Vincent De Keyzer
> > [mailto:vincent at dekeyzer.net]
> > > Sent: 24 January 2005 14:02
> > > To: cisco-voip at puck.nether.net
> > > Subject: [cisco-voip] CCM - Leading zeroes on
> > calling number
> > >
> > >
> > >
> > > Hello,
> > >
> > >
> > >
> > > I am facing (maybe because I'm in Europe) a
> > cosmetic issue with
> > > CallManager and a Cisco2821 as gateway.
> > >
> > >
> > >
> > > When I receive an incoming call on the gateway,
> > the set-up message
> > > appears as follows:
> > >
> > >
> > >
> > > Jan 24 14:45:16.918 CET: ISDN Se0/0/0:15 Q931: RX
> > <- SETUP pd = 8
> > > callref = 0x7194
> > >
> > >         Sending Complete
> > >
> > >         Bearer Capability i = 0x8090A3
> > >
> > >                 Standard = CCITT
> > >
> > >                 Transer Capability = Speech
> > >
> > >                 Transfer Mode = Circuit
> > >
> > >                 Transfer Rate = 64 kbit/s
> > >
> > >         Channel ID i = 0xA9838A
> > >
> > >                 Exclusive, Channel 10
> > >
> > >         Calling Party Number i = 0x2181,
> > '23334455'
> > >
> > >                 Plan:ISDN, Type:National
> > >
> > >         Called Party Number i = 0xA1, '24447722'
> > >
> > >                 Plan:ISDN, Type:National
> > >
> > >         Sending Complete
> > >
> > >
> > >
> > > When the call hits my IP phone, it shows calling
> > number '23334455'
> > > instead of what I had wished, which is '023334455'
> > (since it's a
> > > national call).
> > >
> > >
> > >
> > > In the same way, for an international call from,
> > say, France, I would
> > > receive on the PRI '33612345678' and 'Type:
> > International', which I
> > > would like to appear on the display of the IP
> > phone as '0033612345678'.
> > >
> > >
> > >
> > > How can I add one or two zeros to the calling
> > number based depending on
> > > its type ('National' or 'International')?
> > >
> > >
> > >
> > > Vincent
> > >
> > >
> > >
> >
> _____________________________________________________________________
> > > This message has been checked for all known
> > viruses by the MessageLabs
> > > Virus Control Centre.
> > >
> > >
> > >
> > > _______________________________________________
> > > cisco-voip mailing list
> > > cisco-voip at puck.nether.net
> > >
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> 
> 
> 
> 
> __________________________________
> Do you Yahoo!?
> The all-new My Yahoo! - Get yours free!
> http://my.yahoo.com
>