[cisco-voip] Question on PRI Gateway
Anthony Mendoza
amendoza at Niku.com
Mon Jun 20 21:01:53 EDT 2005
yeah, I'll remove it. The config I started with didn't have it, I just
added it to try and get the system to register..
-Anthony
> -----Original Message-----
> From: Erick Bergquist [mailto:erickbe at yahoo.com]
> Sent: Monday, June 20, 2005 5:56 PM
> To: Anthony Mendoza; Ryan Ratliff
> Cc: cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] Question on PRI Gateway
>
>
> Also, remove the application mgcpapp from pots
> dial-peer with PRI port under it. That can cause you
> problems with calls. There is a bug id on that not
> being needed but some cisco docs conflict and we went
> through TAC before on that when we had issues with
> calls on PRI off and on and since removing that we
> haven't had issues. I can dig up the bug id if you
> need it.
>
> --- Anthony Mendoza <amendoza at Niku.com> wrote:
>
> > That did it, thanks!
> >
> > -Anthony
> > -----Original Message-----
> > From: Ryan Ratliff [mailto:rratliff at cisco.com]
> > Sent: Monday, June 20, 2005 10:47 AM
> > To: Anthony Mendoza
> > Cc: cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] Question on PRI Gateway
> >
> > You will need to completely remove the pri-group
> > command before adding
> > service mgcp.
> >
> > Another thing you can enable is ccm-manager config.
> > This will let CM
> > configure your PRI for you.
> >
> > -Ryan
> > On Jun 20, 2005, at 1:39 PM, Anthony Mendoza wrote:
> >
> > dial-peer voice 1 pots
> > application mgcpapp
> > port 1/0:23
> >
> > I added the above, but still get:
> > rwc-faxgw-149-59(config-if)#isdn bind-l3 ?
> > q931 Select IOS Q.931
> >
> > I also verified service mgcp:
> > rwc-faxgw-149-59(config)#controller T1 1/0
> > rwc-faxgw-(config-controller)#shut
> > rwc-faxgw-(config-controller)#pri-group timeslots
> > 1-24 service mgcp
> > rwc-faxgw-(config-controller)#no shut
> > rwc-faxgw-(config-controller)# Jun
> > 20 10:32:50.487 PDT: %CONTROLLER-5-UPDOWN:
> > Controller T1 1/0, changed
> > state t o administratively down Jun 20 10:32:50.743
> > PDT:
> > %CONTROLLER-5-UPDOWN: Controller T1 1/0, changed
> > state t o up Jun 20
> > 10:32:50.995 PDT: %CONTROLLER-5-UPDOWN: Controller
> > T1 1/0, changed state
> > t o down (LOF detected) Jun 20 10:32:56.035 PDT:
> > %CONTROLLER-5-UPDOWN:
> > Controller T1 1/0, changed state t o up
> > rwc-faxgw-(config-controller)#end rwc-faxgw-149-59#
> >
> > What else am I missing? I actually copied my base
> > config from a 2651
> > gateway of ours so I don't know why it isn't working
> > :(
> >
> > Also not sure why the service mgcp doesn't stick to
> > the pri-group config
> > on the controller.
> >
> > -Anthony
> > -----Original Message-----
> > From: cisco-voip-bounces at puck.nether.net
> > [mailto:cisco-voip-bounces at puck.nether.net] On
> > Behalf Of Anthony Mendoza
> > Sent: Monday, June 20, 2005 7:48 AM
> > To: rratliff at cisco.com
> > Cc: cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] Question on PRI Gateway
> >
> > I think the pots dialper is the missing one.
> > --------------------------
> > Anthony Mendoza
> > Senior Infrastructure Manager
> > t: 650-298-5955
> > c: 510-579-1909
> > f: 208-247-5501
> > e: amendoza at niku.com
> >
> > -----Original Message-----
> > From: Ryan Ratliff <rratliff at cisco.com>
> > To: Anthony Mendoza <amendoza at Niku.com>
> > CC: Cisco VoIP <cisco-voip at puck.nether.net>
> > Sent: Mon Jun 20 07:47:38 2005
> > Subject: Re: [cisco-voip] Question on PRI Gateway
> >
> > Your pri-group should end in 'service mgcp'
> >
> > If you can't bind l3 to ccm-manager then I *think*
> > you need a pots
> > dial-peer with 'port 1/0:23' and 'application
> > MGCPAPP'.
> >
> > -Ryan
> > On Jun 20, 2005, at 10:38 AM, Anthony Mendoza wrote:
> >
> > I thought that too, but don't have that option :(
> > Any ideas with the
> > below info?
> >
> > rwc-faxgw-149-59(config-if)#isdn bind-l3 ?
> > q931 Select IOS Q.931
> >
> > Here's some relevant config:
> >
> > ccm-manager redundant-host 10.150.4.12 10.150.0.13
> > ccm-manager mgcp
> > ccm-manager music-on-hold !
> > !
> > controller T1 1/0
> > framing esf
> > linecode b8zs
> > pri-group timeslots 1-24
> >
> > interface Serial1/0:23
> > no ip address
> > no logging event link-status
> > loopback local
> > isdn switch-type primary-dms100
> > isdn incoming-voice voice
> > no cdp enable
> > voice-port 1/0:23
> > !
> > mgcp
> > mgcp call-agent 10.150.4.11 service-type mgcp
> > version 0.1 mgcp
> > dtmf-relay voip codec all mode out-of-band mgcp rtp
> > unreachable timeout
> > 1000 action notify mgcp package-capability
> > rtp-package mgcp
> > package-capability sst-package no mgcp
> > package-capability fxr-package no
> > mgcp timer receive-rtcp mgcp sdp simple mgcp fax t38
> > inhibit mgcp rtp
> > payload-type g726r16 static
> >
> > rwc-faxgw-149-59#sho ver
> > Cisco Internetwork Operating System Software IOS
> > (tm) 3600 Software
> > (C3640-IS-M), Version 12.3(13), RELEASE SOFTWARE
> > (fc2)
> > Technical Support: http://www.cisco.com/techsupport
> > Copyright (c)
> > 1986-2005 by cisco Systems, Inc.
> > Compiled Thu 10-Feb-05 04:28 by ssearch
> > Image text-base: 0x60008B00, data-base: 0x61BE6000
> >
> > ROM: System Bootstrap, Version 11.1(20)AA2, EARLY
> > DEPLOYMENT RELEASE
> > SOFTWARE (fc1)
> > ROM: 3600 Software (C3640-IS-M), Version 12.3(13),
> > RELEASE SOFTWARE
> > (fc2)
> >
> > rwc-faxgw-149-59 uptime is 18 hours, 58 minutes
> > System returned to ROM
> > by reload at 12:37:26 PDT Sun Jun 19 2005 System
> > restarted at 12:38:56
> > PDT Sun Jun 19 2005 System image file is
> > "flash:c3640-is-mz.123-13.bin"
> >
> > cisco 3640 (R4700) processor (revision 0x00) with
> > 92160K/6144K bytes of
> > memory.
> > Processor board ID 24397072
> > R4700 CPU at 100MHz, Implementation 33, Rev 1.0
> > Bridging software.
> > X.25 software, Version 3.0.0.
> > SuperLAT software (copyright 1990 by Meridian
> > Technology Corp).
> > Primary Rate ISDN software, Version 1.1.
> > 1 FastEthernet/IEEE 802.3 interface(s)
> > 24 Serial network interface(s)
> > 1 Channelized T1/PRI port(s)
> > DRAM configuration is 64 bits wide with parity
> > disabled.
> > 125K bytes of non-volatile configuration memory.
> > 32768K bytes of processor board System flash
> > (Read/Write)
> >
> > Configuration register is 0x1921
> >
> > -Anthony
> >
> > > -----Original Message-----
> > > From: Ryan Ratliff [mailto:rratliff at cisco.com]
> > > Sent: Monday, June 20, 2005 7:31 AM
> > > To: Anthony Mendoza
> > > Cc: Tim Frazee; Cisco VoIP
> > > Subject: Re: [cisco-voip] Question on PRI Gateway
> > >
> > > Make sure you have the 'isdn bind-l3 ccm-manager'
> > command on your
> > > Serial interface for the PRI. I'd guess right now
> > that MGCP isn't
> > > trying to backhaul your PRI.
> > >
> > > -Ryan
> > > On Jun 20, 2005, at 10:20 AM, Anthony Mendoza
> > wrote:
> > >
> > > I plugged in the loop back and the interface looks
> > up, but still not
> > > registering:
> > >
> > > Interface IHQ IQD OHQ OQD
> > RXBS RXPS
> > > TXBS TXPS TRTL
> > >
> >
> --------------------------------------------------------------
> > > ----------
> > > * FastEthernet0/0 0 0 0 0
> > 11000 21
> > > 1000 2 0
> > > Serial1/0:0 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:1 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:2 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:3 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:4 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:5 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:6 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:7 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:8 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:9 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:10 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:11 0 0 0 0
> > 0 0
> > > 0 0 0
> > >
> > > Interface IHQ IQD OHQ OQD
> > RXBS RXPS
> > > TXBS TXPS TRTL
> > >
> >
> --------------------------------------------------------------
> > > ----------
> > > Serial1/0:12 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:13 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:14 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:15 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:16 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:17 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:18 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:19 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:20 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:21 0 0 0 0
> > 0 0
> > > 0 0 0
> > > Serial1/0:22 0 0 0 0
> > 0 0
> > > 0 0 0
> > > * Serial1/0:23 0 0 0 0
> > 0 0
> > > 0 0 0
> > >
> > > rwc-faxgw-149-59#sho mgcp endpoint
> > >
> > > Interface T1 1/0
> > >
> > > ENDPOINT-NAME V-PORT SIG-TYPE
> > ADMIN
> > >
> > >
> > > rwc-faxgw-149-59#
> > >
> > > Any ideas for me?
> > >
> > > Thanks,
> > > -Anthony
> > >
> > >> -----Original Message-----
> > >> From: Anthony Mendoza
> > >> Sent: Sunday, June 19, 2005 7:17 PM
> > >> To: Tim Frazee; Cisco VoIP
> > >> Subject: RE: [cisco-voip] Question on PRI Gateway
> > >>
> > >> Thanks! I'll get my loopback plugged in
> > tomorrow!
> > >>
> > >>
> > >> -Anthony
> > >> -----Original Message-----
> > >> From: Tim Frazee [mailto:tfrazee at aosgs.com]
> > >> Sent: Sunday, June 19, 2005 4:27 PM
> > >> To: Anthony Mendoza; Cisco VoIP
> > >> Subject: RE: [cisco-voip] Question on PRI Gateway
> > >>
> > >> You will need at least layer 2 to register.
> > >>
> > >> I normally plug in a loopback plug for staging.
> > >>
> > >>
> > >>
> > >> Timothy Frazee
> > >> Enterprise Engineer
> > >> AOS Global Solutions
> > >>
> > >> Cisco IP Phone: 636.680.1065
> > >> Cellular Phone: 314.753.7506
> > >> -----Original Message-----
> > >> From: cisco-voip-bounces at puck.nether.net
> > >> [mailto:cisco-voip-bounces at puck.nether.net] On
> > Behalf Of Anthony
> > >> Mendoza
> > >> Sent: Sunday, June 19, 2005 1:45 PM
> > >> To: Cisco VoIP
> > >> Subject: [cisco-voip] Question on PRI Gateway
> > >>
> > >> I've got my 3640 properly configured (or so I
> > believe), but it isn't
> > >> showing up as registered on my CCM (4.x).. To me
> > it appears as
> > >> though the gateway is properly configured as it
> > shows as being
> > >> "registered" to the primary CCM (my subscriber).
> > >>
> > >> Here's what I see on the gateway:
> > >>
> > >> rwc-faxgw-149-59#sho ccm-manager
> > >> MGCP Domain Name: rwc-faxgw-149-59.niku.com
> > >> Priority Status Host
> > >>
> >
> ============================================================
> > >> Primary Registered
> > 10.150.4.11
> > >> First Backup Backup Ready
> > 10.150.4.12
> > >> Second Backup Backup Ready
> > 10.150.0.13
> > >>
> > >> Current active Call Manager: 10.150.4.11
> > >> Backhaul/Redundant link port: 2428
> > >> Failover Interval: 30 seconds
> > >> Keepalive Interval: 15 seconds
> > >> Last keepalive sent: 13:41:25 PDT Jun
> > 19 2005
> > >> (elapsed time:
> > >> 00:00:07)
> > >> Last MGCP traffic time: 13:41:25 PDT Jun
> > 19 2005
> > >> (elapsed time:
> > >> 00:00:07)
> > >> Last failover time: None
> > >> Last switchback time: None
> > >> Switchback mode: Graceful
> > >> MGCP Fallback mode: Not Selected
> > >> Last MGCP Fallback start time: None
> > >> Last MGCP Fallback end time: None
> > >>
> > >> Configuration Error History:
> > >> FAX mode: cisco
> > >>
> > >> And
> > >>
> > >> rwc-faxgw-149-59#show mgcp
> > >> MGCP Admin State ACTIVE, Oper State ACTIVE -
> > Cause Code NONE MGCP
> > >> call-agent: 10.150.4.11 Initial protocol service
> > is MGCP
> > >> 0.1 MGCP block-newcalls DISABLED MGCP send SGCP
> > RSIP:
> > >> forced/restart/graceful/disconnected DISABLED
> > MGCP quarantine mode
> > >> discard/step MGCP quarantine of persistent events
> > is ENABLED MGCP
> > >> dtmf-relay voip codec all mode out-of-band MGCP
> > dtmf-relay for VoAAL2
> >
> > >> disabled for all codec types MGCP voip modem
> > passthrough disabled
> > >> MGCP voaal2 modem passthrough disabled MGCP voip
> > modem relay:
> > >> Disabled.
> > >> MGCP TSE payload: 100
> > >> MGCP T.38 Named Signalling Event (NSE) response
> > timer: 200 MGCP
> > >> Network (IP/AAL2) Continuity Test timer: 200 MGCP
> > 'RTP stream loss'
> > >> timer disabled MGCP request timeout 500 MGCP
> > maximum exponential
> > >> request timeout 4000 MGCP rtp unreachable timeout
> > 1000 action notify
> > >> MGCP gateway port: 2427, MGCP maximum waiting
> > delay 3000 MGCP restart
> >
> > >> delay 0, MGCP vad DISABLED MGCP rtrcac DISABLED
> > MGCP system resource
> > >> check DISABLED MGCP xpc-codec: DISABLED, MGCP
> > persistent hookflash:
> > >> DISABLED MGCP persistent offhook: ENABLED, MGCP
> > persistent
> > >> onhook: DISABLED MGCP piggyback msg ENABLED, MGCP
> > endpoint offset
> > >> DISABLED MGCP simple-sdp ENABLED MGCP
> > undotted-notation DISABLED MGCP
> >
> > >> codec type g711ulaw, MGCP packetization period 20
> > MGCP JB threshold
> > >> lwm 30, MGCP JB threshold hwm 150 MGCP LAT
> > threshold lwm 150, MGCP
> > >> LAT threshold hwm 300 MGCP PL threshold lwm 1000,
> > MGCP PL threshold
> > >> hwm 10000 MGCP CL threshold lwm 1000, MGCP CL
> > threshold hwm 10000
> > >> MGCP playout mode is adaptive 60, 40, 200 in msec
> > MGCP Fax Playout
> > >> Buffer is 300 in msec MGCP media
> > >> (RTP) dscp: ef, MGCP signaling dscp: af31 MGCP
> > default
> > >> package: trunk-package MGCP supported packages:
> > gm-package
> > >> dtmf-package trunk-package line-package
> > >> hs-package rtp-package
> > ms-package dt-package
> >
> > >> mo-package
> > >> mt-package sst-package
> > MGCP Digit Map
> > >> matching order: shortest match SGCP Digit Map
> > matching
> > >> order: always left-to-right MGCP VoAAL2
> > ignore-lco-codec DISABLED
> > >> MGCP T.38 Fax is DISABLED MGCP T.38 Fax ECM is
> > ENABLED MGCP T.38 Fax
> > >> NSF Override is DISABLED MGCP T.38 Fax Low Speed
> > Redundancy: 0MGCP
> > >> T.38 Fax High Speed
> > >> Redundancy: 0
> > >> MGCP control bind :DISABLED
> > >> MGCP media bind :DISABLED
> > >> MGCP Upspeed payload type for G711ulaw: 0,
> > G711alaw: 8 MGCP Static
> > >> payload type for G.726-16K codec MGCP Dynamic
> > payload type for
> > >> G.726-24K codec MGCP Dynamic payload type for
> > G.Clear codec MGCP
> > >> Guaranteed scheduler time is disabled
> > >>
> > >> What appears to be missing? Let me know if you
> > need config
> > >> snippets...
> > >> Now, my PRI is not plugged in yet, but I didn't
> > think that was
> > >> necessary.. Any tips are greatly appreciated!!
> > >>
> > >> Thanks,
> > >> --
> > >> Anthony Mendoza
> > >>
> > >>
> > >> --
> > >> No virus found in this outgoing message.
> > >> Checked by AVG Anti-Virus.
> > >> Version: 7.0.323 / Virus Database: 267.7.8/22 -
> > Release Date:
> > >> 6/17/2005
> > >>
> > >>
> > >>
> > >> CONFIDENTIALITY NOTICE: The information contained
> > in this
> > > message and
> > >> or attachments is intended only for the person or
> > entity to which it
> > >> is addressed and may contain confidential and/or
> > privileged
> > > material. Any
> > >> review, retransmission, dissemination, copying,
> > or other use of this
> > >> information by persons or entities other than the
> > intended recipient
> > >> is prohibited. If you received this e-mail or its
> > attachments in
> > >> error, please contact the sender and delete the
> > material from any
> > > system and
> > >> destroy any copies.
> > >>
> > >>
> > >
> > >
> > > CONFIDENTIALITY NOTICE: The information contained
> > in this message and
> > > or attachments is intended only for the person or
> > entity to which it
> > > is addressed and may contain confidential and/or
> > privileged material.
> > > Any review, retransmission, dissemination,
> > copying, or other use of
> > > this information by persons or entities other than
> > the intended
> > > recipient is prohibited. If you received this
> > e-mail or its
> > > attachments in error, please contact the sender
> > and delete the
> > > material from any system and destroy any copies.
> > >
> > > _______________________________________________
> > > cisco-voip mailing list
> > > cisco-voip at puck.nether.net
> > >
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> > >
> > >
> >
> >
> > CONFIDENTIALITY NOTICE: The information contained in
> > this message and or
> > attachments is intended only for the person or
> > entity to which it is
> > addressed and may contain confidential and/or
> > privileged material. Any
> > review, retransmission, dissemination, copying, or
> > other use of this
> > information by persons or entities other than the
> > intended recipient is
> > prohibited. If you received this e-mail or its
> > attachments in error,
> > please contact the sender and delete the material
> > from any system and
> > destroy any copies.
> >
> >
> >
> > CONFIDENTIALITY NOTICE: The information contained in
> > this message and or
> > attachments is intended only for the person or
> > entity to which it is
> > addressed and may contain confidential and/or
> > privileged material. Any
> > review, retransmission, dissemination, copying, or
> > other use of this
> > information by persons or entities other than the
> > intended recipient is
> > prohibited. If you received this e-mail or its
> > attachments in error,
> > please contact the sender and delete the material
> > from any system and
> > destroy any copies.
> >
> >
> >
> > CONFIDENTIALITY NOTICE: The information contained in
> > this message and or
> > attachments is intended only for the person or
> > entity to which it is
> > addressed and may contain confidential and/or
> > privileged material. Any
> > review, retransmission, dissemination, copying, or
> > other use of this
> > information by persons or entities other than the
> > intended recipient is
> > prohibited. If you received this e-mail or its
> > attachments in error,
> > please contact the sender and delete the material
> > from any system and
> > destroy any copies.
> >
> >
> >
> > CONFIDENTIALITY NOTICE: The information contained in
> > this message and
> > or attachments is intended only for the person or
> > entity to which it is
> > addressed and may contain confidential and/or
> > privileged material. Any
> > review, retransmission, dissemination, copying, or
> > other use of this
> > information by persons or entities other than the
> > intended recipient is
> > prohibited. If you received this e-mail or its
> > attachments in error,
> > please contact the sender and delete the material
> > from any system and
> > destroy any copies.
> >
> > > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
>
>
>
>
> ____________________________________________________
> Yahoo! Sports
> Rekindle the Rivalries. Sign up for Fantasy Football
> http://football.fantasysports.yahoo.com
>
CONFIDENTIALITY NOTICE: The information contained in this message and
or attachments is intended only for the person or entity to which it is
addressed and may contain confidential and/or privileged material. Any
review, retransmission, dissemination, copying, or other use of this
information by persons or entities other than the intended recipient is
prohibited. If you received this e-mail or its attachments in error,
please contact the sender and delete the material from any system and
destroy any copies.
More information about the cisco-voip
mailing list