[cisco-voip] Configuring Cisco 2811 for voice

[Teodor Georgiev]

Ok. Surely Samsung DCS Euro can be interconnected with Cisco. Guaranteed.
You should check the E1 card model installed inside the Samsung.

If the card supports ISDN, then why don't you interconnected the DCS and Cisco 
using ISDN PRI? 

Is there some particular reason on using R2?

Btw, I have docs on configuring the DCS PBX. Maybe the PC software as well, 
but not sure.

On Tuesday 01 August 2006 17:32, you wrote:
> I was told that it is a EURO DCS, and we have an E1 card in the Cisco.
> The R2 works for the controller card, as it brings up the E1 without
> problems. In fact the far end can call to Mexico, but it hangs up after
> 8 seconds. The call completes!
>
> However, outgoing calls seize the port, but sends no digits. I thought
> maybe this was a interdigit timing issue and made some adjustments. But
> again nothing worked.
>
> Keep in mind that the Samsung rep in Mexico stated that they had to
> 'modify' this equipment to get it through Customs. I am still trying to
> get the answer as to what they modified.
>
> Thank you
> Darel Graham
>
>
>
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Teodor Georgiev
> Sent: Tuesday, August 01, 2006 7:03 AM
> To: cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] Configuring Cisco 2811 for voice
>
>
>  Darel,
>
> Samsung DCS PBXes work pretty fine with Cisco voice gateways.
>
> 1. There are several types of this PBX --> DCS Compact / 2, iDCS, DCS
> Euro.
>
> I doubt your model is iDCS, because it is a NG-model with VoIP
> capabilities
> and LAN port for management (other have only RS-323 and SIM management
> options).
>
> The Compact models do not support R2, they support only ISDN PRA and
> BRA. So,
> I suppose your model is not Compact as well.
>
> Check and report your exact model. See the card types you have (E&M, E1
> R2,
> PRI). If you have an ISDN card, you can configure it for ETSI or QSIG.
>
> I am not aware of the T1 cards for Samsung DCS PBXes however. Are you
> sure it
> is really R2 MFC over E1 ?
>
> On Tuesday 01 August 2006 16:43, Graham, Darel wrote:
> > Hi all,
> >
> > I've run up against a problem with a Samsung DCS that has been
>
> modified
>
> > to get it in to Mexico.
> > Bad way to start, I know.
> >
> >
> > The customer states that this is set for R2MFC, dtmf and E&M wink or
> > immediate start. I have tried variations of Cisco configurations for
>
> R2,
>
> > and none worked.
> > Is there anyone that knows the secret to this configure this pbx? BTW
> > Samsung rep in Mexico stated that they have not been able to get a
>
> Cisco
>
> > to work with it. Of course they didn't say that they had any router
> > working with it either.
> >
> > So, if anybody wants a crack at it I'll be glad to try whatever
>
> (within
>
> > reason) to get this to work. I'll be the first to admit I'm not an
> > expert on this type of configuration.
> >
> > If you wish to contact me to discuss this further just e-mail me
> > directly. And thank you for those that respond.
> >
> > Darel Graham
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip