[cisco-voip] Setting up local DSP resources on 2821
Ted Nugent
tednugent69 at yahoo.com
Mon Aug 7 16:25:31 EDT 2006
Are you showing the PVDM2-16 as well?
You can try changing the codec complexity but I
believe this is already the default
voice-card 0
codec complexity flex
Here's a "snippet" from the DSP calc
======================
voice-card 0
codec complexity flex
Set of Conferencing/Transcoding commands when used
with PVDM2-XX DSPs:
sccp local <local interface>
sccp ccm <call manager IP address> identifier <ccm ID
#> version <version #>
sccp
!
sccp ccm group 999
bind interface <local interface>
associate ccm <ccm ID #> priority 1
associate profile <conferencing profile ID #>
register <conference bridge name>
associate profile <transcoding profile ID #>
register <transcoder name>
!
dspfarm profile <transcoding profile ID #> transcode
maximum sessions 4
associate application SCCP
dspfarm profile <conferencing profile ID #> conference
maximum sessions 2
associate application SCCP
====================
--- "Ortiz, Carlos" <CORTIZ at broward.org> wrote:
> In this case I am configuring a 2811 running
> 12.4(9)T. The show diag
> shows me this whick makes sense since I ordered the
> PVDM 16 to 32
> upgrade :
>
> PVDM Slot 0:
> 32-channel (G.711) Voice/Fax PVDMII DSP SIMM
> PVDM daughter card
> Hardware Revision : 4.0
> Part Number : 73-8539-05
> Board Revision : A0
> Deviation Number : 0
> Fab Version : 04
> PCB Serial Number : FOC101818WH
> RMA Test History : 00
> RMA Number : 0-0-0-0
> RMA History : 00
> Processor type : 00
> Product (FRU) Number : PVDM2-32
>
> I was able to create the profiles for conferencing
> and transcoding. I
> am able to put max sessions for transcoding to 4,
> but I am not able to
> select anything but 0 for conf. see below:
>
> Lowrise(config)#dspfarm profile 1 conference
> Lowrise(config-dspfarm-profile)#maximum sessions ?
> <0-0> Number of sessions assigned to this profile
>
> I have a T1 WIC and a T1-1MFT card in the router but
> not sure why I
> can't select sessions for the conf br.
>
> Any clues would be appreciated.....
>
>
> -----Original Message-----
> From: Ted Nugent [mailto:tednugent69 at yahoo.com]
> Sent: Monday, August 07, 2006 2:45 PM
> To: Ryan Ratliff; Ortiz, Carlos
> Cc: Erik Erasmus (E); cisco-voip at puck.nether.net;
> Ted Nugent
> Subject: Re: [cisco-voip] Setting up local DSP
> resources on 2821
>
> You also need to configure your devices in CM as
> "Enhanced IOS devices" in case thats not clear in
> the
> doc.
>
> --- Ryan Ratliff <rratliff at cisco.com> wrote:
>
> > The PDVM2s require the dspfarm profile
> > configuration. Yes you do
> > have to associate the profile to a sccp ccm group.
> >
> > -Ryan
> >
> > On Aug 7, 2006, at 2:12 PM, Ortiz, Carlos wrote:
> >
> > This is a response to a 3 week old post. Did you
> > guys ever get this
> > working? I am reading through the documentation
> and
> > it's a bit
> > confusing. You guys posted part of a config below,
> > but I am reading and
> > they mention Associating a DSP Farm Profile to a
> > Cisco Unified
> > CallManager Group. Did you have to do this?
> >
> > Which example would you follow for onboard ISR
> > 28XX/38xx router PVDM2
> > configuration??
> >
> > Carlos
> >
> > -----Original Message-----
> > From: cisco-voip-bounces at puck.nether.net
> > [mailto:cisco-voip-bounces at puck.nether.net] On
> > Behalf Of Erik Erasmus
> > (E)
> > Sent: Tuesday, July 18, 2006 3:55 PM
> > To: Wydra, Jason; Ted Nugent;
> > cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] Setting up local DSP
> > resources on 2821
> >
> >
> > I was wondering about the same thing
> >
> > I will have a PVDM2-8 for normal termination of
> the
> > BRIs and probably
> > a PVDM2-32 for the conferencing /transcoding
> >
> >
> >
> > Erik Erasmus
> >
> >
> > -----Original Message-----
> > From: cisco-voip-bounces at puck.nether.net
> > [mailto:cisco-voip-bounces at puck.nether.net] On
> > Behalf Of Wydra, Jason
> > Sent: 18 July 2006 09:46 PM
> > To: Ted Nugent; cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] Setting up local DSP
> > resources on 2821
> >
> > One more thing with the following....
> >
> > voice-card 0
> > dspfarm
> > dsp services dspfarm
> >
> > If I run a show diag, I see two PVDM2-32 modules.
> > One is slot 0 and
> > the
> > other is slot 1. Does the voice-card command above
> > denote the actual
> > slot number of the PVDM? Reason I ask is because I
> > want the PVDM in
> > slot
> > 0 to do transcoding and the PVDM in slot 1 to do
> > conferencing. When I
> > try to configure the following I get this:
> >
> > ft-worth(config)#voice-card 1
> > ^
> > % Invalid input detected at '^' marker.
> >
> > ft-worth(config)#voice-card ?
> > <0-2> Voice interface slot #
> >
> > ft-worth(config)#voice-card
> >
> >
> > Thanks,
> > Jason
> > -----Original Message-----
> > From: Ted Nugent [mailto:tednugent69 at yahoo.com]
> > Sent: Tuesday, July 18, 2006 12:46 PM
> > To: Wydra, Jason; cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] Setting up local DSP
> > resources on 2821
> >
> > You need it all... confusing at first but after
> you
> > set it up a couple times it's not so bad.
> >
> > Makes me miss the old NM-HDV config :-/
> >
> >
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgc
> > r/
> > vvfax_c/callc_c/ccm_c/intcnf2.htm#wp1061433
> >
> > voice-card 0
> > dspfarm
> > dsp services dspfarm
> > !
> > !
> > sccp local FA0/0
> > sccp ccm <pub-ipaddr> identifier 2 version 4.0
> > sccp ccm <sub-ipaddr> identifier 1 version 4.0
> > sccp ip precedence 3
> > sccp
> > !
> > sccp ccm group 1
> > associate ccm 2 priority 2
> > associate ccm 1 priority 1
> > associate profile 2 register <site>xcode
> > associate profile 1 register <site>conf
> > keepalive retries 5
> > switchover method immediate
> > switchback method immediate
> > switchback interval 15
> > !
> > dspfarm profile 2 transcode
> > codec g711ulaw
> > codec g711alaw
> > codec g729ar8
> > codec g729abr8
> > codec gsmfr
> > maximum sessions 12
> > associate application SCCP
> > !
> > dspfarm profile 1 conference
> > codec g711ulaw
> > codec g711alaw
> > codec g729ar8
> > codec g729abr8
> > codec g729r8
> > codec g729br8
> > maximum sessions 8
> > associate application SCCP
> >
> >
>
=== message truncated ===
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
More information about the cisco-voip
mailing list