[cisco-voip] Setting up local DSP resources on 2821

[Erik Erasmus (E)]

I was wondering about the same thing

I will have a PVDM2-8 for normal termination of the BRIs and probably
a PVDM2-32 for the conferencing  /transcoding 



Erik Erasmus


-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Wydra, Jason
Sent: 18 July 2006 09:46 PM
To: Ted Nugent; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Setting up local DSP resources on 2821

One more thing with the following....

voice-card 0
 dspfarm
 dsp services dspfarm

If I run a show diag, I see two PVDM2-32 modules. One is slot 0 and
the
other is slot 1. Does the voice-card command above denote the actual
slot number of the PVDM? Reason I ask is because I want the PVDM in
slot
0 to do transcoding and the PVDM in slot 1 to do conferencing. When I
try to configure the following I get this:

ft-worth(config)#voice-card 1
                            ^
% Invalid input detected at '^' marker.

ft-worth(config)#voice-card ?
  <0-2>  Voice interface slot #

ft-worth(config)#voice-card


Thanks,
Jason
-----Original Message-----
From: Ted Nugent [mailto:tednugent69 at yahoo.com]
Sent: Tuesday, July 18, 2006 12:46 PM
To: Wydra, Jason; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Setting up local DSP resources on 2821

You need it all... confusing at first but after you
set it up a couple times it's not so bad.

Makes me miss the old NM-HDV config :-/

http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgc
r/
vvfax_c/callc_c/ccm_c/intcnf2.htm#wp1061433

voice-card 0
 dspfarm
 dsp services dspfarm
!
!
sccp local FA0/0
sccp ccm <pub-ipaddr> identifier 2 version 4.0
sccp ccm <sub-ipaddr> identifier 1 version 4.0
sccp ip precedence 3
sccp
!
sccp ccm group 1
 associate ccm 2 priority 2
 associate ccm 1 priority 1
 associate profile 2 register <site>xcode
 associate profile 1 register <site>conf
 keepalive retries 5
 switchover method immediate
 switchback method immediate
 switchback interval 15
!
dspfarm profile 2 transcode
 codec g711ulaw
 codec g711alaw
 codec g729ar8
 codec g729abr8
 codec gsmfr
 maximum sessions 12
 associate application SCCP
!
dspfarm profile 1 conference
 codec g711ulaw
 codec g711alaw
 codec g729ar8
 codec g729abr8
 codec g729r8
 codec g729br8
 maximum sessions 8
 associate application SCCP


--- "Wydra, Jason" <jwydra at Burwood.com> wrote:

> Does anyone have a good example config on how to set
> this up? I have two
> onboard PVDM2 32 channel modules in my 2821. I want
> the local router to
> hit the gateway first for MTP, Conference and
> Transcoding. Then CCM
> 4.1.3. I have the Cisco procedure but I'm wondering
> if I really need to
> configure everything they are suggesting. Looks like
> it might require
> multiple dspfarm profiles for all the services I
> want to provide.
>
> 
>
> Thanks,
>
> 
>
> Jason Wydra
>
> 
>
> > _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around
http://mail.yahoo.com


_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This e-mail and its contents are subject to the Telkom SA Limited
e-mail legal notice available at
http://www.telkom.co.za/TelkomEMailLegalNotice.PDF
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~