[cisco-voip] Setting up local DSP resources on 2821

[McLean Pickett]

Jason -

Voice-card 0 just refers to the PVDM resources on the motherboard.
Voice-card 1 would be a network module populated with PVDM's.

McLean

-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Wydra, Jason
Sent: Tuesday, July 18, 2006 3:46 PM
To: Ted Nugent; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Setting up local DSP resources on 2821

One more thing with the following....

voice-card 0
 dspfarm
 dsp services dspfarm

If I run a show diag, I see two PVDM2-32 modules. One is slot 0 and the
other is slot 1. Does the voice-card command above denote the actual
slot number of the PVDM? Reason I ask is because I want the PVDM in slot
0 to do transcoding and the PVDM in slot 1 to do conferencing. When I
try to configure the following I get this:

ft-worth(config)#voice-card 1
                            ^
% Invalid input detected at '^' marker.

ft-worth(config)#voice-card ?
  <0-2>  Voice interface slot #

ft-worth(config)#voice-card


Thanks,
Jason
-----Original Message-----
From: Ted Nugent [mailto:tednugent69 at yahoo.com]
Sent: Tuesday, July 18, 2006 12:46 PM
To: Wydra, Jason; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Setting up local DSP resources on 2821

You need it all... confusing at first but after you set it up a couple
times it's not so bad.

Makes me miss the old NM-HDV config :-/

http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/
vvfax_c/callc_c/ccm_c/intcnf2.htm#wp1061433

voice-card 0
 dspfarm
 dsp services dspfarm
!
!
sccp local FA0/0
sccp ccm <pub-ipaddr> identifier 2 version 4.0 sccp ccm <sub-ipaddr>
identifier 1 version 4.0 sccp ip precedence 3 sccp !
sccp ccm group 1
 associate ccm 2 priority 2
 associate ccm 1 priority 1
 associate profile 2 register <site>xcode  associate profile 1 register
<site>conf  keepalive retries 5  switchover method immediate  switchback
method immediate  switchback interval 15 !
dspfarm profile 2 transcode
 codec g711ulaw
 codec g711alaw
 codec g729ar8
 codec g729abr8
 codec gsmfr
 maximum sessions 12
 associate application SCCP
!
dspfarm profile 1 conference
 codec g711ulaw
 codec g711alaw
 codec g729ar8
 codec g729abr8
 codec g729r8
 codec g729br8
 maximum sessions 8
 associate application SCCP


--- "Wydra, Jason" <jwydra at Burwood.com> wrote:

> Does anyone have a good example config on how to set this up? I have 
> two onboard PVDM2 32 channel modules in my 2821. I want the local 
> router to hit the gateway first for MTP, Conference and Transcoding. 
> Then CCM 4.1.3. I have the Cisco procedure but I'm wondering if I 
> really need to configure everything they are suggesting. Looks like it

> might require multiple dspfarm profiles for all the services I want to

> provide.
> 
>  
> 
> Thanks,
> 
>  
> 
> Jason Wydra
> 
>  
> 
> > _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
> 


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 


_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip