[cisco-voip] CCM4.1 to GK to MCU...

[Jonathan Charles]

Got that on the trunk config...

Jonathan

On 10/30/06, Andreas Pentenrieder <voip at pentenrieder.de> wrote:
>
>  when using a default-technology make sure that the callmanager also has a
> tech-prefix of 1#....
>
> Andi
>
> ----- Original Message -----
>
> *From:* Jonathan Charles <jonvoip at gmail.com>
> *To:* Ryan Ratliff <rratliff at cisco.com>
> *Cc:* Cisco Voip <cisco-voip at puck.nether.net>
> *Sent:* Monday, October 30, 2006 9:07 PM
> *Subject:* Re: [cisco-voip] CCM4.1 to GK to MCU...
>
> I checked again, and that subnet has a /22 on it, so it covers the entire
> region...
>
> I ran the debugs and saw this:
>
>
> value RasMessage ::= registrationReject :
>     {
>       requestSeqNum 47
>       protocolIdentifier { 0 0 8 2250 0 4 }
>       rejectReason discoveryRequired : NULL
>     }
>
>
>
>
> Jonathan
>
> On 10/30/06, Ryan Ratliff < rratliff at cisco.com> wrote:
> >
> > Check that zone subnet command.  I'm pretty sure it restricts what IP
> > addresses the gatekeeper will allow registration from.  Also check
> > out 'debug ras', 'debug h225 asn1', and 'debug gatek main 10'.
> >
> > -Ryan
> >
> > On Oct 30, 2006, at 1:52 PM, Jonathan Charles wrote:
> >
> > There is a route-pattern pointing to the trunk, but the Gatekeeper
> > only shows the MCU registered as an endpoint.
> >
> > The CM is set to register as a gateway... and the CM is not on the
> > same subnet...
> >
> >
> >
> > Jonathan
> >
> > On 10/30/06, Ryan Ratliff < rratliff at cisco.com> wrote: You have to
> > have a route pattern pointing to the trunk for CM to
> > register with the gk afaik.  Also note that CM only retries
> > registration every 30-60 seconds.  For quicker results reset the gk-
> > controlled trunk.  Also make sure you have CM set to register as a
> > gateway not a terminal.
> >
> > From your config I assume CM's IP address falls within the
> > 10.1.1.0/22 subnet?
> >
> > -Ryan
> >
> > On Oct 30, 2006, at 12:38 PM, Jonathan Charles wrote:
> >
> > OK, I have a CCM4.1 box, and I am trying to get it to connect (for
> > video) to a Cisco MCU, via a gatekeeper...
> >
> > The MCU is registered to the gatekeeper as an endpoint, but I can't
> > get the CCM to do the same...
> >
> > I have a gatekeeper controlled trunk pointing at the MCU (with the GK
> > identified)...
> >
> > Still nothing...
> >
> > I also added a couple of route-patterns (with the MCU service
> > prefixes) pointing at the trunk... Still nothing...
> >
> >
> > gatekeeper
> >    zone local 10.1.1.1 binky.com
> >    zone subnet 10.1.1.1 10.1.1.0/22 enable
> >    zone prefix 10.1.1.1 2125554244*
> >    gw-type-prefix 1#* default-technology
> >    no shutdown
> >
> >
> >
> > Any ideas?
> >
> > TIA
> >
> >
> >
> > Jonathan
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> >
>  ------------------------------
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20061030/56a1bddf/attachment-0001.html