[cisco-voip] Caller-id and name debugging

[Ryan Ratliff]

It can be in a few places actually.

In the CCMAdmin page for this endpoint do you have "Display IE Outbound"
checked?  This is required for CM to present the Display IE in the Q931
Setup message. 

It will require a reset of the gateway to take affect (will drop calls).  If
you have 'ccm-manager config' enabled simply reset it via CCMAdmin.  If you
are not using that feature you will need to do a 'no mgcp/mgcp' on the
router.

-Ryan 
-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of bababooey at cox.net
Sent: Monday, September 25, 2006 12:29 PM
To: Aman Chugh
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Caller-id and name debugging

>From the Voice-GW, debug q931. This is a call from CCm to PBX.
Where is the calling name supposed to be?

2811#
*Sep 25 16:32:16.651: ISDN Se1/0/0:23 Q931: TX -> SETUP pd = 8  callref =
0x0003 
        Bearer Capability i = 0x8090A2 
                Standard = CCITT 
                Transfer Capability = Speech  
                Transfer Mode = Circuit 
                Transfer Rate = 64 kbit/s 
        Channel ID i = 0xA98397 
                Exclusive, Channel 23 
        Net Specific Fac i = 0x00E6 
        Calling Party Number i = 0x0081, '5670800' 
                Plan:Unknown, Type:Unknown 
        Called Party Number i = 0x80, '2757001' 
                Plan:Unknown, Type:Unknown *Sep 25 16:32:16.671: ISDN
Se1/0/0:23 Q931: RX <- CALL_PROC pd = 8  callref = 0x8003 
        Channel ID i = 0xA98397 
                Exclusive, Channel 23
*Sep 25 16:32:16.675: ISDN Se1/0/0:23 Q931: RX <- ALERTING pd = 8  callref =
0x8003 
        Progress Ind i = 0x8081 - Call not end-to-end ISDN, may have in-band
info *Sep 25 16:32:36.235: ISDN Se1/0/0:23 Q931: TX -> DISCONNECT pd = 8
callref = 0x0003 
        Cause i = 0x8090 - Normal call clearing *Sep 25 16:32:36.247: ISDN
Se1/0/0:23 Q931: RX <- RELEASE pd = 8  callref = 0x8003 *Sep 25
16:32:36.267: ISDN Se1/0/0:23 Q931: TX -> RELEASE_COMP pd = 8  callref =
0x0003 2811#


---- Aman Chugh <aman.chugh at gmail.com> wrote: 
> debug isdn q931.
> 
>
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186
a0080237271.shtml
> 
> Aman
> 
> 
> On 9/25/06, Bob A. Bowie <bababooey at cox.net> wrote:
> >
> > Hello, I have a CCM 4.1.3 with an mgcp gw running a PRI on 2811 isr.
> > I am trying to pass caller-id name and number, i am getting the calling
> > number but not the name.
> >
> > Which debug do I need to run on the voice gw to see if the info is
> > passing?
> > Which CCM trace would display if the call manager is sending and
receiving
> > the info?
> >
> > Thanks.
> >
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip