[cisco-voip] PRI MGCP

[Ahmed Elnagar]

Thanks Ryan for ur reply. just want to tell u that the returning dial peer that it will match on to get back to the device is using sip protocol
 
dial-peer voice 4000195 voip
 description Test_Fax
 destination-pattern 195
 session protocol sipv2
 session target ipv4:30.3.1.7
 dtmf-relay rtp-nte
 codec g711ulaw
 fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
 no vad
 
 
will the command allow connection h323to-h323 be effective in this case?
 
 
 
 
Thanks and Best Regards

Ahmed A. Elnagar
Network Field Engineer
 
Advanced Computer Technology (ACT)
16 Fawzy Ramah St.Off Shehab St.Mohandessin, Giza, Egypt 
Postal Code:12411 Cairo Egypt

Mob: +2010-2833868
Website: www.act-eg.com
E-mail: aelnagar at act-eg.com

________________________________

From: Ryan Ratliff [mailto:rratliff at cisco.com]
Sent: Wed 18-Apr-07 2:58 PM
To: Ahmed Elnagar
Cc: 'cisco-voip at puck-nether.net'
Subject: RE: [cisco-voip] PRI MGCP


AFAIK a pots dial-peer pointing to an MGCP controlled PRI will not work.
 
Try adding the commands:
voice service voip
  allow connection h323-to-h323
 

-Ryan 

 

________________________________

From: Ahmed Elnagar [mailto:aelnagar at ACT-EG.COM] 
Sent: Wednesday, April 18, 2007 8:50 AM
To: Ryan Ratliff
Cc: cisco-voip at puck-nether.net
Subject: RE: [cisco-voip] PRI MGCP


that is exactly what I did. I made a route pattern to return the call to the gateway. the problem is that the returned call doesnot match the voip dial-peer that is poiting to the device that I want to forward the call to. it is only matching any pots dial peer if it has a match. aslo for this device to go out through the router is it possible to do a pots dial peer poinitng to the PRI at the smae time it is MGCP controllered? 
 
Thanks and Best Regards

Ahmed A. Elnagar
Network Field Engineer
 
Advanced Computer Technology (ACT)
16 Fawzy Ramah St.Off Shehab St.Mohandessin, Giza, Egypt 
Postal Code:12411 Cairo Egypt

Mob: +2010-2833868
Website: www.act-eg.com
E-mail: aelnagar at act-eg.com

________________________________

From: Ryan Ratliff [mailto:rratliff at cisco.com]
Sent: Wed 18-Apr-07 2:40 PM
To: Ahmed Elnagar
Cc: 'cisco-voip at puck-nether.net'
Subject: RE: [cisco-voip] PRI MGCP


You would have to have the gateway added to CM as an H.323 gateway as well as MGCP.  Then you have to use a route pattern to hairpin the call back to the H.323 process on the router.  There is no way to do this in the gateway itself.  All calls on an MGCP controlled PRI are sent to CM.
 

-Ryan 

 

________________________________

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Ahmed Elnagar
Sent: Wednesday, April 18, 2007 8:26 AM
Cc: cisco-voip at puck-nether.net
Subject: [cisco-voip] PRI MGCP



Hello;

again regarding the PRI configuration.

is it possible to configure the gateway in MGCP and make the PRI E1 MGCP controllered and then select a certain dialed number from the E1 range to be forwared to another device using a VOIP dial peer on the router instead forwarding the call to the callmanager.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070418/af5351d2/attachment-0001.html