[cisco-voip] H.323 Gateway PRI selection

[Linsemier, Matthew]

I think that Gurpinder's idea is the best then.  Basically prepend
digits in CallManager so when the H.323 gateway gets them it knows which
dial peer to use.  Calling number can then be set based on the dial
peer. 


Matt

 

From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of
CarlosOrtiz at bayviewfinancial.com
Sent: Wednesday, June 06, 2007 4:03 PM
To: Lelio Fulgenzi
Cc: cisco-voip-bounces at puck.nether.net; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] H.323 Gateway PRI selection

 


Basically I need 3 different groups of users always to use their
designated PRI's so that the correct caller ID is presented.   Think of
it as 3 companies sharing one gateway, each desginated to a PRI with
that companies name and number on it.   

In response to the Gurpinder's post....I do not need them to select
which caller id they want to use.  Each of the 3 groups will always use
the same caller ID.  I had an idea similar to yours to prepend digits so
that when the call gets to the gateway I know which PRI it needs to exit
from. I just want to make sure I don't miss an easier method. 

Carlos 




"Lelio Fulgenzi" <lelio at uoguelph.ca> 
Sent by: cisco-voip-bounces at puck.nether.net 

06/06/2007 03:50 PM 

To

<cisco-voip at puck.nether.net>, <CarlosOrtiz at bayviewfinancial.com> 

cc

	
Subject

Re: [cisco-voip] H.323 Gateway PRI selection

 

		




Wouldn't you do this with the dial-peers? 
  
There is a caller ID config statement that you can configure, then
select the appropriate port. 
  
------------------------------------------------------------------------
--------
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
"Buffalo buffalo Buffalo buffalo buffalo buffalo Buffalo buffalo."
WJR 
----- Original Message ----- 
From: CarlosOrtiz at bayviewfinancial.com 
To: cisco-voip at puck.nether.net 
Sent: Wednesday, June 06, 2007 2:24 PM 
Subject: [cisco-voip] H.323 Gateway PRI selection 


We have a new H.323 Gateway that will have 4 PRI's.  2 PRI's will be
grouped together and present one caller  ID.  Each of the remaining 2
PRI's will have their own caller ID (3 total different Caller ID's).
How can you select a specific PRI to be used so that the correct caller
ID is shown depending on which phone dials outboud?  I should be able to
prepend a digit on Call Mgr to the 3 different route patterns (different
partitions) and then route the call based on the leading digit found on
the H.323 GW.  I know I can do this via MGCP easily as well.  Any other
good ideas or thoughts about this via H.323? 

Carlos 

________________________________

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip_____________________
__________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip


CONFIDENTIALITY STATEMENT
This communication and any attachments are CONFIDENTIAL and may
be protected by one or more legal privileges. It is intended
solely for the use of the addressee identified above. If you
are not the intended recipient, any use, disclosure, copying
or distribution of this communication is UNAUTHORIZED. Neither
this information block, the typed name of the sender, nor
anything else in this message is intended to constitute an
electronic signature unless a specific statement to the
contrary is included in this message. If you have received this
communication in error, please immediately contact me and delete
this communication from your computer. Thank you.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070606/b4193b99/attachment-0001.html