[cisco-voip] getting dial-tone when dialing into FXO port while in SRST mode

[Lelio Fulgenzi]

OK - Thanks. I wasn't sure about that. I was going to (and have) tested reloads to see if that command sticks and it looks like it does.

For a minute it looked liked it added the MGCP dialpeers at the end of the config but it looks like I didn't save the previous reorder.

Correct me if I'm wrong, but unless I want to send calls out these FXO ports, I don't need a dial-peer at all do I?


--------------------------------------------------------------------------------
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
"Buffalo buffalo Buffalo buffalo buffalo buffalo Buffalo buffalo."      WJR

  ----- Original Message ----- 
  From: Erick Bergquist 
  To: Lelio Fulgenzi 
  Cc: cisco-voip at puck.nether.net 
  Sent: Tuesday, June 12, 2007 6:33 PM
  Subject: Re: [cisco-voip] getting dial-tone when dialing into FXO port while in SRST mode


  The connection plar command is what you need with FXOs in H.323 (SRST)
  mode. The MGCP config push won't remove it.

  On 6/12/07, Lelio Fulgenzi <lelio at uoguelph.ca> wrote:
  >
  >
  > Ok, I know this is simple, but I can't find the solution. Or at least what I
  > think I need.
  >
  > While in SRST mode, when I dial into the FXO port I get dial-tone. I need it
  > to go to a particular number. In my readings, I see that you can configure
  > "connection plar" on the voice port, but from what I gather I'm not supposed
  > to add config statements to the voice port when I'm using "ccm-manager
  > config".
  >
  > I reordered my dial-peers so the 999020 is at the top and my 20 is after it.
  > I thought I could add the "incoming called number" like I did on the PRIs,
  > but no go. I was thinking I just needed to configure the dial-peer voice 20
  > to modify the inbound calling number to match my extension.
  >
  > Any ideas?
  >
  > !
  > dial-peer voice 999020 pots
  >  service mgcpapp
  >  port 0/2/0
  > !
  > dial-peer voice 20 pots
  >  incoming called-number 61001
  >  port 0/2/0
  > !
  >
  >
  >
  > When I dial in I get
  >
  > .Jun 12 18:10:25: %CALL_CONTROL-6-APP_NOT_FOUND: Application mgcpapp in
  > dial-peer 999020 not found.  Handing callid 11 to the alternate app Default.
  >
  >
  >
  > --------------------------------------------------------------------------------
  > Lelio Fulgenzi, B.A.
  > Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
  > (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
  > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  > "Buffalo buffalo Buffalo buffalo buffalo buffalo Buffalo buffalo."      WJR
  >
  > _______________________________________________
  > cisco-voip mailing list
  > cisco-voip at puck.nether.net
  > https://puck.nether.net/mailman/listinfo/cisco-voip
  >
  >
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070612/5b79bc1b/attachment-0001.html